Difference between revisions of "Constructor:Creating new pieces"
Pavel.Gordon (Talk | contribs) (→Preparation for digitizing) |
Pavel.Gordon (Talk | contribs) (→Preparation to digitization) |
||
| Line 128: | Line 128: | ||
== Inputting pieces though digitizer (Digitizing) == | == Inputting pieces though digitizer (Digitizing) == | ||
| − | === Preparation | + | === Preparation for digitization === |
To start digitization (archiving) of a piece: | To start digitization (archiving) of a piece: | ||
Revision as of 10:44, 6 March 2015
Creation of new pieces
There are several ways to create new pieces in a model:
1) Export of pieces from “Designer” program
2) Input of pieces through a digitizer (Digitizing)
3) Copying (and opening) of pieces from other models
4) Conversion of pieces from the formats of other systems (Gerber, Assyst, etc.)
5) Creation of pieces within a model: copying, standard pieces, etc.
6) Creation of pieces with the help of macrocommandsExport of pieces from “Designer” program
Contents
- 1 Export of pieces from “Designer” program
- 2 Inputting pieces though digitizer (Digitizing)
- 3 Coping pieces from other models
- 4 Converting pieces from formats of other systems
- 5 Creating new pieces inside a model
- 6 Creating pieces with the help of macrocommands
Export of pieces from “Designer” program
To export pieces from “Designer” program for creation of base constructions:
· Create a new model or open a previously created model in the window “Work with the database” (
- “Object/ Work with the database”).
· Select PIECES tab in the horizontal menu and the button in it
or follow the text menu points “Piece/Do the project”. The window for selection of a project is displayed on the screen.
· Select the button for opening projects in “Designer” program
on the top panel of the window.
· Select the group of projects with pressing the button of the drop-down list

· Select the project for exporting in “Projects” window with highlighting the line of a necessary construction

· Select the pieces of the project in “Pieces” window with clicking the cell before the name of the piece, to mark it with a check mark
. Another click in the cell removes selection.
- selection of all the pieces in the list,
- cancel selection of pieces,
- cancel colored selections (errors)
Open the table with “Reference data” of the construction with selection of the button
and make necessary changes in the tabs “Measurement data”, “Increases and constant values”, “Variables”:

Measurement data – values of measurement of a figure, used for construction;
Increases and constant values– increases and constant values for the project;
Variable values – values received by means of calculations (formulas);
· To confirm new data, press the YES button, to cancel changes press the CANCEL button
· Select piece sizes with marking of all sizes/heights with the help of the top switch
, or by means of selection of necessary sizes with a click in the corresponding cells of the table:
The button
allows to clear the table and cancel selection of sizes
· Press the button
to export pieces to “Constructor” program.
· For constant values of the table input manually and not received from the “Size database” (increases etc.) the windows with the “List of missing pieces” for all but basic size are displayed on the screen.

By means of inputting new values (instead of available ones) for each size, you can receive a gradable value (for example, length of the garment input in the table as a constant value). Even if no changes were made, it is compulsory to confirm values for a current size.
When the option is switched off
the window “List of missing data” is not displayed (if it is not necessary to change the table data by size).
· The pieces of selected sizes will be displayed on the screen of “Constructor” program.
FEATURES 1) The pieces are exported as untitled and must be assigned names (the function
”Pieces/ Piece parameters”) in “Constructor” program.
It is not compulsory for the name to match the one in “Designer” program, since an internal number of this piece is used in the program. You can have pieces with the same name from different projects in one model in “Designer” program.
2) The window “Piece parameters” shows the project name and the piece name.

When switching on the parameter
in the export window, such link with the base is lost.
Such pieces are marked with the letter D in the corresponding line of the window “Work with the database”. When a piece is deleted in “Designer” program, this indicator is switched off. When a piece is copied or opened on the screen from a different model, the marking D remains, and when pieces are copied inside a model, it is switched off.
3) The size scale of the working model must match the “Size database” of the project. Correspondence of basic sizes is not compulsory.
The range of sizes in the working model of “Constructor” program should be the same, or less than the range of sizes in the “Size database” of the project in “Designer” program. Otherwise, the following message will be displayed on the screen:

At the same time only one size, not the whole graded piece, will be exported.
This message will also be displayed if the size scales of the project made in “Designer” program and the working model do not match. For example, when a project of standard sizes (Industry Standard, State Standard Specification) is exported to a model with the European scale (34,36,38…). In this case, you need to Set the table for “Size compliance”.
Set the table for «Size compliance»
· Press the ОК button in the message and select the button for size selection
on the top panel of the export window. The table for size compliance is displayed on the screen.
For example, a project with the database of sizes 84 – 120 and heights 158 – 170 must be input in a model with the size range 36 – 48. Select height 164 for export.
· Specify the line with a necessary size/height in “Old sizes” column (it is highlighted), and then select a corresponding cell in the size table of the working model, filling in “New sizes” column. Upon wrong selection of the line, click it again to deselect.

When selection is finished, press the YES button. Switch to the export window is done.
Further operations are similar to those when the size scales of the model and the project comply.
The table commands:
- clear the table;
and
- save and read data from file.
FEATURES
1) When exporting pieces from the project containing widths to the project without it and complete match of sizes, you need to use a working width from the “Reference data” table of the project in “Designer” program.
2) When pieces are exported from the project containing widths to the project containing widths, corresponding widths are exported (regardless of the working width in “Designer” program).
3) If the size ranges are different, you need to select an export width in the Compliance table and select TO WHICH WIDTH of the model it should be changed, with opening of the size tab on the right side in the export window. In this case, it does not matter, which working width is opened on the screen in “Designer” program.

4) “Rewrite” option in the export window allows to export pieces size by size

ATTENTION!!! When ONE size is exported to the screen of “Constructor” program, a working size of “Designer” program is displayed on the screen of “Constructor”. That is why it is important to conform the basic size of the “Constructor” model in and the working size of the “Designer” project (in “Reference data” table
of the export window).

5) When the pieces are input repeatedly from “Designer” program with change in reference data (Measurement data, increases) previously input pieces are automatically reconstructed according to the new data.
6) The pieces are transferred to “Constructor” with constructed seams and modifications (ledge, cuff), if they were created in “Designer”, but only upon the first export. If you modify the seams in “Designer”, the information about the seams made in “Constructor” will be used upon repeated export.
Inputting pieces though digitizer (Digitizing)
Preparation for digitization
To start digitization (archiving) of a piece:
· Switch on the digitizer
· Create a new model or load a previously created model in the window “Work with the database” (File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image001.gif- “Object/ Work with the database”) to input digitized pieces in the model.
· Select the PIECE tab and the button File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image002.gifin the tab
You can also follow the text menu points “Piece/ Input from digitizer”.
The window with the parameters of an archived piece is displayed on the screen
· Fill in the piece parameters: Material, Name, Number of cut pieces
Specify the size and the height of the piece, and specify the type of the main contour being input: Cut or Ready view.
If necessary, change the other piece parameters in this window.
· To confirm data, press the YES button, to cancel input of data, press CANCEL button
The working window for piece archiving is displayed on the screen. The image on the screen reflects the process performed on the digitizer. The current working mode is displayed on the top panel of the window: digitization stage at the current moment. The button panel for digitization operations is displayed in the lower left corner; it corresponds with the template panel of the digitizer commands. When an optical cursor (a special mouse) is moved on the digitizer surface, the cursor cross is moved on the screen.
The button panel commands:
Clear – Clear the digitizer field upon wrong input of a piece.
Close contour – Close the piece contour for exact splicing of the last and the starting input points (to avoid trying to match the starting point when the input of the contour is finished).
Cancel the last point - Delete the last point (or points) input by mistake.
Save – Save a digitized piece in the end of the process.
Continue input – Mode for inputting of the second part of the piece when a piece is digitized in parts.
Input of point marker – Inputting inner contour as a point.
Input of the internal contour – Input of an internal contour for making marks and working lines.
Input by graded piece – Input of points with uneven gradation size by size
Exit – Exit from the archiving window when the process is finished.
The commands from the button panel of the digitizer are set in one of the following ways:
a) Set the optical cursor in the line of a necessary command of the template digitizer menu on the digitizer and click one of the cursor buttons.
b) Select the necessary line of the button archiving menu on the monitor screen with the help of the mouse.
The piece points on the digitizer are read with pressing a corresponding cursor button:
Button 1 - Intermediate points creating shape, which only affect shaping of a curve. Their visibility in the program is switched off;
Double click– Dart of an intermediate type (visible on the screen)
Button 2 – Control (grading) intermediate points;
Double click – dart of a corresponding type
Button 3 - End points (grading points of the contour bend)
Double click – dart of a corresponding type
Button 5 - grain line, and an increment by grading points is read
The digitizers working with “Constructor” automated working place can have different types of cursors, so the buttons can be set under the numbers, different from those indicated in the current description.