Design:Working with the screen (for operations with a drawing)

From Julivi Help
Revision as of 19:56, 16 April 2015 by Pavel.Gordon (Talk | contribs) (→‎Select a Line(s))

Jump to: navigation, search

 

           The commands for work with the screen (the left-side button menu) are divided into two groups:

commands of work at the drawing ( design137.png), and commands of work at ready pieces (design138.png).

          Disabled command buttons are not relevant for working in this mode.

          There are commands (Zoom, Contours Visibility, etc.) that work in both modes. Described below are the commands used in the Work at the Drawing mode.

Zooming an Image

 

      While working with a project on the screen, we have to change the image scale. Such actions are preformed with the help of a group of zooming commands on the button bar:


 
design139.png

     These functions can also be performed through the use of the so-called “Hot” keys, that is, the respective keys of the keyboard. These functions are described separately.

«Microscope»

  “Zoom”  

      Use the “Zoom” function to view a certain screen area zoomed in. For this purpose you have to:

§  Fulfill the “Screen / Microscope” menu item or choose the design140.png command in the button menu. The cursor will look likedesign141.png.

§  Move the cursor intersection in the screen to an imagined angle of the screen area you want to zoom in.

§  Still holding down the left button, move the cursor on the screen. Upon that, the required screen area will be selected with a rectangular frame.

§  Release the mouse button after the part of the screen you want to view has been selected.

Show all on the screen

After fulfilling the “Screen / Show All” menu item or choosing the design142.png command in the button menu, you can see the entire drawing or all the pieces in the screen scale.

Return to previous scale

After the image scale has been changed, you can return to the previous variant. For that purpose, fulfill the “Screen / Return Scale” menu items, or choose thedesign143.png button.

Zoom out

To zoom out gradually, choose the design144.png button, or the “Screen /Zoom Out” menu item. The image size will continue reducing every time the button is pressed.

Zoom in

To zoom in gradually, choose thedesign145.png button, or the “Screen / Zoom In” menu item. The image size will continue increasing every time the button is pressed.

The second method of performing the “Zoom Out” and “Zoom In” functions for the image:

For a mouse with a central scroll wheel: - when the wheel is rotated up, the size of the image around the cursor is reducing; - when the wheel is rotated down, the size of the image around the cursor is increased. This operation is performed simultaneously with the work of other commands: you can use the scroll wheel without the need to stop performing the current command.

Move an Image

 

      If you want to move an image on the screen, perform the following actions:

§  Fulfill the “Screen / Move Image” menu item or perform the design146.png command in the button menu. The cursor will look like design147.png.

§  Point the cursor intersection at any element of the screen and, holding down the mouse button, move the image to the required place on the screen, and then release the mouse button.

 

        The second method of performing this function: For a mouse with a central scroll wheel, -

 If you press and hold the wheel, the function of moving the image will be performed;

         This operation is performed simultaneously with the work of other commands: you can use the scroll wheel without the need to stop performing the current command.

Operations with Axes

       The design148.png command block of the left-side button menu is used for working with coordinate axes on the screen.

·         To display the axes on the screen, choose the design149.png button or fulfill the “Screen / Show / Remove Coordinate Axes” menu items. Then the coordinate axes will be set in a random place of the screen.

·         To set the origin of coordinates into the required point of the screen, choose the design150.png  button or fulfill the “Screen / Move the Coordinate Axes into Point” menu items. The cursor will look like design151.png. Click the left mouse button to place the cursor intersection into any required point of the screen or construction element.

·         To rotate a coordinate axis along some line or by an arbitrary angle, choose the design152.png button or fulfill the “Screen / Rotation of Coordinate Axes” menu items. Then the cursor will look like design153.png. Holding the left mouse button, move the X or Y axis line, placing it into the required point or line, and then release the left mouse button.

 

·         To place the axis into the standard position (angle of 0), to rotate the axis by a defined angle, or to view the angle that the axis was rotated by the “Rotation of Axes” command, you have to fulfill the “Screen / Set Coordinate Axes Angle” menu item or choose the design154.png button. Then a dialog box will be displayed on the screen, where the angle value of the angle rotation is specified (if it was rotated):

 
design155.png


 - After viewing the rotation angle value, press the design156.png button if you need only the information about the angle value. In this case, the axis will remain on the screen unchanged.

- You can enter the axis turn value (45) manually and press the design157.png button.

- You can set the axis into the standard position after the turns by choosing the design158.png button.

 

·         During the work you can use the cursor coordinates line in the lower right corner of the screen:


 design159.png

    After calling up the axes onto the screen and placing them into the desired point you can move the cursor arrowhead to the required point of the screen as precisely as possible and, without moving the mouse, find the value:

          The first cell shows the Х coordinate value,

          The second one shows the Y coordinate value,

          The third one shows the straight-line distance from the center of coordinates to the arrowhead.

Clearing the Screen

To clear the screen from temporary selections and “trash”, choose the design160.png button or fulfill the “Screen / Redraw Screen” menu item.

«Rollback» (Cancel Command)

 

        The “Rollback” function allows you to perform step-by-step cancellation of actions from the last work stage to the level of saving into the base. To perform a rollback, do the following:

·         Choose the design161.png button or fulfill the “Project / Cancel a Command” menu items.   

When the algorithm is corrected in the “Program Checkout” window (the design162.png button), while being at a certain stage in the middle of the algorithm and performing operations of deleting or replacing an operator, you can cancel an erroneous action. During rollback, the actions of algorithm correction in the middle of the text will be canceled one-by one, and then, as usual, the last commands will be canceled from bottom to top.

     When the project is saved into the database (the design163.png  button or the “Project / Save” text menu items) the “Rollback” button will be disabled.

Cancellation of “Rollback” (Undo Command)

 

    If “rollback” was performed by mistake, but the project has not yet been saved in the base, you should use the “Rollback” cancellation function. For this purpose, do the following:

·         Choose the design164.png button or fulfill the “Project / Redo a Command” menu items.

     The design165.png button becomes active after the first rollback is performed, and enables you to cancel the “Rollback” by redoing its action.

     For both the “Rollback” buttons to become disabled again, perform the “Saving into Database” operation (the design166.png button or the “Project / Save” menu items).

Visibility of Various Drawing Elements on the Screen

     When there is much visual information on the screen, it can be difficult to figure it out: there are many contours, lines, points, names of lines and points, and so on. There are situations when you need to indicate a certain line for performing a function, but it becomes superimposed on another one. To correct such problems there is a possibility to disable visibility of some contours, lines, points, etc. on the screen.

      In the button menu there is a group of buttons meant for working with visibility of construction elements. There are all types of drawing elements represented on these buttons.

design167.png                           

Successively from left to right, from top to bottom:

1) circles, 2) arcs, 3) curved lines, 4) points, 5) names of points, 6) contours (cuts, inner contours, grains), 7) intervals, 8) straight lines, 9) names of lines,10) elements of basic net, 11) explanatory text.

 

            A button with the image of a construction element allows you to disable its visibility by clicking the left mouse button. The selected element is not cleared from the screen but becomes invisible.

            If visibility of an element is disabled, it will not be drawn when the drawing or pieces are printed out on the printer and plotter.

 

ATTENTION! Do not forget to enable visibility of the element again (by a left-click on the relevant button), otherwise you will not be able to continue working with it.

 

Screen Shifts (for the Drawing)

 

        In the left-side button menu there is the commands block for screen shifts. They are meant for checking of matching and line configurations between the drawing elements.

       These operations are of screen nature, therefore actions performed with the pieces do not impact on their actual state and position on the screen. In fact, they are screen copies of the selected objects (pieces, their parts, and lines) that are displayed on the screen.

     In the regular working mode of the program all the commands of screen shifts are disabled, except the command for selecting the required objects for matching, and after choosing the  design179.png button, the commands become functional: 

design180.pngdesign181.png

Select a Line(s)

 

    In order to perform screen shift on a drawing, you have to select a line or a group of lines.          

    To select lines, do the following:

·         Press the  design183.png button. Then the cursor will look likedesign184.png

·         Select a line or a group of lines, which have to be modified (at that, the selected objects are highlighted in color.) For this, do the following:

 Variant 1:        

         Indicate the required lines one by one by clicking the left mouse button. If a line is selected by mistake, the selection and highlighting in color will disappear after a repeated click on the same line.

 

Variant 2:

        Press and hold the SHIFT key on the keyboard, then seize the group of lines into a frame while holding the left mouse button. After releasing the SHIFT key you can deselect the non-required lines, pointing the cursor at them and clicking the left mouse button.

 

·         Click the right mouse button after you have selected the lines.

·         In order to create new groups for matching them to one another, repeat this whole process, with other elements already.

 

Each new group will be colored with a different color. If groups are matched to one another, the group being shifted will acquire the color of the stationary group, and then these groups become an integrated coupling (group) already.


Special feature

 

                             

                              The colors of groups on the screen are set in the “Pieces Group” field of the design185.png configuration window.

design186.png

 

Here the desired colors for the first 20 groups are assigned, and the 21st group will be colored with the 1st group’s color. To set the color, click the left mouse button on the square of the color that needs to be changed. At that, the screen for setting colors will be displayed, where you have to choose the required color and press the ОК button.

 

·         After viewing the matching (or making adjustments, as will be described below), you need to deselect the groups. To do so, press the design187.png button, and point the cursor intersection at the group to be deleted. If it is only one, it will be deleted automatically.

At that, screen copies disappear, and changes in the original pieces remain.

 

·         To cancel each matching and return the actions with the given group one step back, choose the design188.png button of the left-side button menu and indicate a certain group.

It is after performing some command that the button becomes active.

 

For example, a project of a jacket (Fig.1) is displayed on the screen:


design189.png
                                                                               Fig.1

 

 

·         Using the design190.png button (as described above), select the scye line (1) and the shoulder line (2) in the front drawing – see Fig.1a.

·         Click the right mouse button to stop selecting lines.

            The selected line(s) will be highlighted in color.

            This is the first group for screen matching.

 

  design191.png                           Fig. 1a

·         Using the design192.png button (as described above), select the lines of shoulder (3), scye (4) and scye dart (5) in the back drawing – see Fig.1b.

·         Click the right mouse button to stop selecting lines.

               The selected line(s) will be highlighted in a different color.

              This is the second group for screen matching design193.png  

 

 

            Fig. 1b

Arbitrary displacement

Rotation at a 90 degree angle

Arbitrary rotation

Mirror

Fold a piece

Restore a piece to initial state

Screen superposition

Superpose piece points

Superpose piece sections

Superpose section ends

Superpose section ends at extension

Program settings

«Hot» keys

Screen scrolling by sizes/ heights/ corpulence values

Screen scrolling of a project

Screen rotation of a drawing

Sketches in a project