Constructor:Generating a new contour
Contents
Creating a new contour
Applying text to a piece
The function of creating additional titled on a piece: name of cuts, line purpose (cut line, line of pocket entry), piece placement (face- inner side).
To apply text on a piece:
·Select the tab CONTOUR and the button
in this tab. The cursor view changes to
.
It is also possible to follow text menu points « Contour/ Apply text».
·Specify 2 spots on a piece (in a point, on a section, or inside a plane of a piece): point of text start (1), point of text direction (2).
Text parameter window is displayed on the screen (contour type
is set by default):
·Enter necessary text and determine its size:
Type required text in the input line
, using any symbols.
Set size of text letters in the line
. A coefficient from a value, set in the program «Utilities» in the tab GLOBAL SETTINGS/ PLOTTER, PIECES, is set in this row.
For example, if size text is set for 1.5cm in the «Utilities», input of a size coefficient 0.5 will create text of 0,75cm in size. ·Press the YES button to confirm input data, press CANCEL to cancel.
Contour Text is created on a piece, it is underlined with a line, drawn through two specified points. This line is invisible when drafting pieces, and its length is of no importance. This line and its both points are used to perform functions with the text contour (for movement, as well as performing other commands of the tab CONTOUR, SECTION, POINT)
1) When the mode
is selected, Size/Height/Corpulence is automatically written on pieces (for drafting pieces as a graded nest on a plotter). To do this, click twice in a required area of a piece, without entering text.
2) An option
allows to save input text parameters (contents and size coefficient) for repeat performance of a function in a different place.
3) It is possible to input text manually as well as select existing text from the list (button
). Lists of standard texts can be created in the program «Utilities», in the tab CONTOUR “TEXT”.
4) It is possible to change properties of an existing contour Text by using the function
- «Contour/ Contour parameters», changing the size of text or the title contents.
This option can be used to create Text of various contents in different sizes. To do so:
·Perform the function of applying text (general) in a regular mode, using the command
of the tab CONTOUR, or by performing text menu points «Contour / Apply text»
·Using the switch of work modes with a graded nest
of the screen menu, switch to the working mode with one (or some) sizes
·Change text to a required size by using the function
- «Contour/Contour parameters":
Having specified the underlining of a text, input new text in a content cell for every size instead of the existing text. Text size coefficient remains the same in all sizes of a graded nest.
1) The size of a text applied to pieces on all models will change automatically if its size is changed in the program «Utilities»!!! That is why text size is set once when the system is launched, and its size for different pieces will depend on the coefficient listed in the window of creating Text contour.
2) To view Text size settings entered in the «Utilities», it is possible to use text menu points «Settings/ Program parameters» in the program «Constructor». It is possible to view data in the tab PLOTTER (cells are blocked):
3) Text placement in graded nest sizes is determined by clicks (1,2) upon setting the text. Increments from specified places are read automatically: if a point is specified - point increment, if a section is specified – ratio of a place of a click to the length of section, if a plane inside a piece is specified – zero increments (text is «nailed» to the screen and is not graded). It is possible to transfer increments to points of a line, underlining the text (working in the Increment table
).
4) For Folded pieces, text will be placed only on one half of a piece after a piece is unfolded in a layout.
5) For Uniform and Blocked pieces, which are in the superposed group with an Active piece, it is possible to apply text in such a way that the 1 and the 2 click of setting the contour are placed on a blocked piece. But the text itself, as well as the contour, always belongs to the active piece.
6) When using modeling commands, Text contour will not change its placement, while being reconstructed like other inner contours.
Create a new arbitrary contour
To create a new contour on a piece:
·Select the tab CONTOUR and the button
in this tab. The cursor view changes to
. It is also possible to follow text menu points «Contour/ Create new».
·Specify the first point - place of beginning a new contour (a section or a point of a piece, or a plane inside a piece).
·Specify the second and following points, creating a contour line of a required shape. If intermediate checkpoint must be made in a specified place, press the <Space> key after clicking the left mouse button, if a final point needs to be made to divide one section from another – press the <Space> key twice.
·Click the right mouse button to stop drawing a line.
The window for selecting contour type and modes of it application is displayed on the screen:
·Select contour type:
- Inner contour, for drafting working lines - mark lines, cut, fold. Contour is not drafted in data layouts.
- Sight contour, for drafting lines, drawn in layouts (pinhole, line).
- Pinhole, for cutting an opening on an automated cutting system.
- Cut line, for cutting a line on an automated cutting system.
- Line of blank direction - similar to Grain line contour to set direction for growing allowance of a blank, created in the window «Piece parameters».
Example of using the contour Line of blank direction:
For example, grain line is located at an angle in a fabric with piece for a piece of neck stitching, and grain line is located across the detail on a piece of adhesive lining.
It is possible to create blanks for both these details in the window «Piece parameters» (function
«Piece/ Piece parameters»), but their form will not be the same in the layout, since these blanks will be grown in different direction with reference to the grain lines:
To solve this problem, it is possible to create a contour of a type «Line of blank direction» by two central points on a piece of a top. This line matches grain line direction on a piece of the adhesive lining, so growing allowances of a blank will be the same for both pieces.
1) The option
allows to cut a section of a contour beyond piece limits (or specified contour limits)
Example of creating yoke contour with limitation and without limitation of a contour:
2) It is possible to create a new contour for all pieces of the group at once in the group of superposed pieces by switching on the mode
. A copy of a given contour is created on each piece.
If the mode
is also used when working with superposed pieces, modeling lines are drafted on all pieces of the group as separate, limited contours:
1) By clicking the right mouse button right after specifying the first point when creating a contour, point contour of zero length will be created. It can be used for work, but it will not be displayed in drafting.
2) If a piece point or section was specified when arbitrary contour was applied, they will be highlighted, and an applied contour will be included in the specified point or line in all sizes. Placement of an arbitrary contour by graded nest sizes is determined by places of clicks upon its creation. Increments from specified points are read automatically: if a point is specified – point increment, if a section is specified - ratio of a click location to the length of a section, if a place inside a piece is specified – zero increments(Contour point is «nailed» to the screen and is not graded). To determine exact placement of contour by sizes, it is recommended to construct it, using specific piece points as reference (pocket mark - from point marks, etc.). If such points are not available, create an arbitrary contour, and then set its location with reference to any point.
3) There are limitations for creating a line outside the border of a piece contour (next to it): - Distance limit to border of information grid equals 5cm for a group of superposed pieces. - For free pieces: the first click is the limit (depending on the scale: small piece – large clearance), there are no limits for the second and others.
4) ATTENTION! Once a figured line is applied, the function
- «Section/ Grade section again» must be performed, to create curve similar to the basic size in various sizes of the graded nest (that is why it is important to create figured contour precisely in the basic size).
5) When locked contour is created (1-2-3-4-5-1) from several sections, to ensure exact connection of the first (1) and the last (5) points, it is recommended to create the last section by using the function of contour lock (
«Contour/ Lock contour»), otherwise a click to the same point (1) may not be exact.
Save a contour as a piece
The function allows to save any of piece contours as a separate independent piece: pocket contour on a forepart can be saved as a piece of a pocket in finished view. By measuring a seam 0,3 – 0,5cm inside a piece, it is possible to save this seam as a piece of an adhesive lining. Having created a seam of variable width on a piece of a top, it can be saves as a piece of lining, etc. To save a contour as a piece:
·Select the tab CONTOUR and the button
in this tab. The cursor view changes to
.
It is also possible to follow text menu points « Contour/ Save as a piece».
·Specify a contour. The window of contour type selection is displayed on the screen:
·Select type of the main contour on a created piece: Cut or Finished view.
ATTENTION! When a contour of type Cut is selected, two contours are automatically created: main contour – Working, and a copying (derived) contour – Cut, which will be drafted in layouts.
·Press the YES button to confirm data input, press CANCEL to cancel.
An untitled piece is displayed on the screen, this piece can be renamed (function
«Piece parameters»)
To open window with piece name in «Piece parameters» at the time of using the function:
·Follow text menu points «Settings/Program parameters»
·Open the tab GENRAL, and in it the tab CONSTRUCTOR
·Select an option «Dialogue «Piece parameters»»
·To save this setting upon the next program launch, press the button SAVE.
In this case, after selecting contour type and pressing the YES button, the window «Piece parameters» is displayed, where name and all necessary parameters of a new piece can be set.
Creating a contour with the help of macrocommands
It is possible to apply contours to existing pieces in one action as per an offered piece with the help of macrocommands (including complex integrated constructions) . Methods of creating such contours are repeated from model to model, only parameters of their construction change. This significantly speeds up process of applying various additional contours on a piece. Constructor can create macrocommands in the program «Macro editor», or use a number of standard constructions, available in the program.
To apply a contour with the help of macrocommands:
·Use text menu point «Macrocommands», in the tab use the group «Contour», «Contour (punch hole marking)», or any other existing group of contour constructions.
·Select a required macrocommand of applying a contour and follow it as per description.
It is possible to open macrocommands with the help of button menu of the program. To do so:
·Select the tab PIECE (not Contour!) and the button
in the tab.
·A window of constructions of the program «Design» is displayed on the screen, with an automatically selected mode for opening macrocommands (the button
is pressed at the tope panel of this window)
·By pressing the button of the drop-down list
, select a group of constructions «Contour», «Contour (punch hole marking)», or any other group of contour constructions in the cell «Group» .
List of macrocommands of a given group is displayed in the window «Project»:
·Specify a line of a required macrocommand and press the button SELECT
·Perform the macrocommand as per description.
Example of applying a contour with the help of a macrocommand
PINHOLE (in a set direction)
To create pinhole contour in a set direction on a piece: ·Select the text menu point «Macrocommands/ Contour/ Pinhole (in a set direction)». The window «Reference data» is displayed on the screen, the window consists of the tab MEASURED DATA – changeable parameters when creating a contour and the tab DESCRIPTION – sketch and description of performing the command.
·Move to the tab DESCRIPTION and read description for performing the command.
·Change reference data of construction in the tab MEASURED DATA, by inputting them in a cell «Value» instead of default data (А and В).
To input values different by size, it is possible to use data of the saved buffer (
) - tab F, or other tabs of the «Calculator». To do so:
1)Click the cell with the left mouse button to select a row (it is highlighted with a blue color).
2)Click the right mouse button. Additional menu is displayed – a list of tabs of the «Calculator».
3)Select a required tab of the list, for example tab F, by clicking the row
.
4) Formula
will be displayed in the cell instead of a number. If necessary, it is possible to enter names of other tabs of the «Calculator» - G, H, I, etc. in other value cells.
· Press YES. The cursor view changes to
.
· Specify a point of Pinhole anchoring, and then specify a point, which sets Pinhole direction Pinhole contour is constructed on a piece in a set direction, at a set distance from the first specified point.
Example of applying a complex contour according to the screen hint outline
Contour of a shawl collar
To create a contour of a shawl collar on a piece of the front:
·Select text menu point «Macrocommands/ Contour/ Shawl collar contour» The window «Reference data» is displayed on the screen, it consists of the tab MEASURED DATA – changeable parameters upon contour construction and DESCRIPTION – sketch and description of command performance.
·Switch to the tab DESCRIPTION and read the description of command performance.
·Change reference data of construction in the tab MEASURED DATA, by inputting them in the cell «Value» instead of default data.
To input values different by size, it is possible to use data of the saved buffer (
) - tab F, or other tabs of the «Calculator» (click the required cell with a left (to highlight a line) and then with a right mouse button, and select a tab name (F, G…) in the floating menu)
·Press YES. The cursor view changes to
.
Outline of order for specifying piece elements (sections, points) is displayed in the top right corner of the screen, and text hints of work order are displayed at the lower panel of the working screen.
·Specify sections and points one by one following the hint: lapel (1), neck of the front (2), shoulder of the front (3), shoulder of the back (4), neck of the back (5), middle cut of the back (6), point of lapel bend (7).
If a section (lapel, shoulder) is cut into sections, specify them while holding down the <SHIFT> key of the keyboard.
Contour of a line for half-overlap, lapel bend and collar is created on a piece of the front.
With the help of the function
-«Modeling/ Assemble a piece» a new piece of the front with a shawl collar is created from contours
Creating lines of a basic grid
It is possible to transfer lines of a basic grid from various projects from the program of constructing core basics «Design» to the «Constructor» (for example, a grid of the core base of a working model).
(Set of lines of the basic grid is created in the program «Design» with the help of the command
- «Lines/ Make a line a part of the basic grid», specifying required lines and points on the screen.)
To transfer lines of the basic grid from a project in «Design» to the «Constructor»:
·Open a previously created or create a new model in the working window of the program «Constructor».
·Select the tab PIECE and the button
in it. It is also possible to follow text menu points «Piece/ Execute project». The window for selecting a project is displayed on the screen
·Select the button
at the top panel of this window
·Select a group of projects: having pressed the button of the drop-down list
, select a required group in the list.
·Select a project for export in the list of the window «Project», by highlighting the line of a required construction The point «Basic grid» is displayed in the window «Piece», if such grid exists in a given project.
·Select an element from the list «Basic grid», by clicking an empty cell in front of a piece to check mark it
.
Further actions and specifics (setting size compliance, etc.) are similar to those described for exporting pieces from the program «Design» to the «Constructor»:
·It is possible to make changes to the reference data of construction (in tabs «Measured data», «Increases and constant values», «Variables» of the reference data table) by selecting the button
·Select piece sizes for export, selecting all sizes with the help of the top switch
, or by selecting required sizes by clicking corresponding cells of a table
The grid is displayed on the screen of the program «Constructor» as a set of inner contours, used for further work: performing the function «Assemble a piece», additional measurements of pieces of the working construction (depth of the cutout, width of cap), etc.
The window «Piece parameters» (
- «Pieces/ Piece parameters») has reduced view for the grid:




























