Constructor:«Calculator»
The dialogue “Calculator”
allows to perform complex calculations with piece measurements (set a required fitting per cent and value, calculate increments, correct
measurements according to the measurement table and do other calculating operations).
To open the “Calculator” window, select the mode
in the table for measurement results
, or select the same button on the “Seam algebra” panel:

The “Calculator” window has a table for sizes and heights of the working model and a top row of functions.
You can fill in the table with the measurement values from the “Seam algebra” buffer
, or from the window with the “Seam algebra”
results
, if press the button
in the same window after inputting the expressions (“'А'/[2]”, etc.)
You can also input values and expressions from the keyboard manually:
After filling in the top main input line and pressing the button
, you can copy this value to the whole graded piece or copy the value to the row (column) of a given size (height)
by clicking the button with the size or height name.
The tab “F” is displayed in the dialogue window of the “Calculator” by default. It contains the buffer last saved in the program. If the buffer is empty, the “Calculator” is displayed without any tabs.
ATTENTION! It is recommended not to do any “F” calculations in this tab, since the data in this tab will be automatically replaced with the values of the last saved buffer.
- add a new tab to the table (in the alphabetical order in English).
- delete a tab.
- the window for input of expressions (formulas). You can write formulas in it by using the existing tabs of the “Measurement results” (A, B, C, D, E) and the “Calculator” (F, G etc).
The letter values are only input in English. Besides, there are linear values (centimeters, millimeters) and nonlinear values (coefficients,
portions, parts).
ATTENTION! In all expressions all nonlinear values should be taken in square brackets.
For example, when multiplying “F *[2]” and dividing “F /[2]”.
After input of formulas, press the button
or
to display the calculation result in the table.
You can input a formula of “G=F/[2]” type and press the button
. The new tab “G” will be automatically
created and will contain the calculated result.

You can create a new tab (“G”, etc.) in advance with selection of the command
, and switch to it.
The formula for this tab can be input as an expression “F/[2]” without the first part “G=”

- calculate the expression value
- put the input data to the buffer
- save the table data in a file
- read the previously saved data from the buffer
- read the previously saved data from the file Select type of value'
Selecting type of a value
The program deals with different types of values: units of length, coefficients, and degrees. While performing calculations, it might be required to change the type of value in the table. To do so, open an additional menu with clicking the right mouse button in the area of values.

At the same time displayed is the menu with a check marked actual type of an opened tab:
Linear value – units of length: centimeters, millimeters, inches
Coefficient – nonlinear values: coefficients, portions, parts. Tab background: yellow
Angle value – value of an angle: degrees. Tab background: green.
To change type of a tab, select the line of a required type in the menu.
Example of changing the type of value
To calculate a ratio while performing the function
- “Point/ Divide a section in ratio”, divide the data from one tab “G” by the data of another tab “H”
of the table.
The result of this will be a nonlinear value (coefficient). To do so:
- Input the division formula “G / 'Н'” in the window for input of expressions of a new tab
- Change the type of the second tab “Н” from “Linear value” to “Coefficient”

- Save the results to the buffer
, and use them while performing the function
, by opening them from the buffer
. You can work without saving them to the buffer: open the result table
in the function window and select the last working tab “I”

FEATURES
While performing different program functions, where you need to input nonlinear values (coefficients or degrees) upon input of data, you can change the type of tab prior to input of data of the saved buffer, or the following message will be displayed on the screen:

This refers to the functions
-“Piece/ Grain line/ Rotate by an angle”;
-“Contour/ Rotate by an angle”;
-“Section/ Rotate by an angle”;
-“Point/ Rotate a section in ratio”
-“Point/ Parameters of the point dividing the
section in ratio”.