Constructor:Basic information about contours
Concept of the main contour of a piece
It is possible to use two types of the main contour in the program – Finished view or Working (in other words, Cut in its initial view, without piece processing constructions – indents, corners, bottom flaps, etc).
It is possible to set seam allowances in outward direction from the main contour Finished view, creating a derived (dependent) Cut contour. And vice versa, it is possible to set seams in inward direction from the main Working contour, creating a derived contour Finished view. Another contour - Cut - dependent on the main contour is automatically created over the Working contour, and copies it in any actions, except functions of the SEAM tab (commands of the final piece processing, meant specifically for the Cut contour)
ATTENTION! It is possible to differentiate the main piece contour on the screen. Contour of the Title point is Yellow for the Finished view, Pink - for the Working contour (according to the color setting “Contours” for main contours)
Work with a piece is done on the main contour (points are shifted, lines are deformed…), and derived contour is automatically reconstructed as per the main contour. An exception to this is the tab SEAMS, used specifically for the derived contour Cut. An emblem of a given construction is created on the screen, by clicking the emblem it is possible to delete or reconstruct the construction according to new parameters.
For example, division of two contours: Cut and Working contour (it maintains view of the initial cut state, without an indent) is done in a piece with the Working contour as the main one when creating an indent (function
«Seams/ Create indent»):
When the shape of the Working contour is changed, Cut contour will be automatically reconstructed along with creating an indent, and it will not need to be created again from the new, changed shape of a piece.
Functions of the tab SEAMS can be performed right on the main contour, construction sections are a part of the main contour excluding modification reconstruction (as with derived contour).
Two options for working with the main contour are seen on the example of processing a vent of the top sleeve:
Title contour
The program supports three options of a title, which contents and placement can change for a specific production (as per client request). Composition for each title type is set in the tab TITLE of the program «Utilities».
To enter required parameters in the title, click the right mouse button in the text area and select required points in the floating list of parameters. Then information MUST be saved for the composition of title to match in «Constructor» and «Utilities».
It is possible to set 1, 2 or 3 type of title for each piece with the help of a function
- «Piece/ Piece parameters» in the program «Constructor». Type 1 is set by default.
A setting for optimizing a title
is available in every piece - it automatically includes title in the Cut contour of a piece (or in the main contour if there is not Cut). Size and placement of a title of any type changes in such a way that it does not extend beyond the Cut line when construction pieces are drafted (a similar mode is also available in the program «Julivi mark»).
General switch for including title is performed in the program «Utilities» (Setting «Insert title in cut» in the tab GLOBAL SETTINGS/ Plotter, pieces). Title size is set in the same panel «Title on a piece»:
These parameters can be viewed (cells are blocked) in the program «Constructor» by following text menu points «Settings/ Program parameters» in the tab PLOTTER:
1) in the program «Utilities», title size for signature 2 (the most complete) is set in the tab TITLE as Size of title text «Text size»
2) When working in the mode «Inserting title in the cut», placement and size of the title will be selected automatically for all 3 title types. In this mode, working with the Title contour is inessential. It is allowed to decrease title parameters upon inserting no more than 10 times.
3) It is possible to differentiate the main contour of a piece with the help of color for the title point: Yellow color for the Finished view, Pink color - for the Working (color settings “Contours” for main contours)
4)These 3 types of title will be used in the program «Plotter» in the mode of creating PIECE OUTLINE (button «Create») instead of the title settings of the plotter program itself
5) Title can be rotated as a regular contour by using the command «Contour/ Rotate(
) , since contour consists of a point (1) and a guiding line with end (2):
6) During screen mirroring Title Point is displayed as an ellipse on the screen, during screen rotations at a particular angle – Title Point will have additional outline.
7) ATTENTION! When pieces are rotated with a screen mirroring, the title will also be mirrored! But upon any piece rotations in the database (the function
- «Piece/ Resort piece») title placement is set according to the piece placement.
8) Functions
«Mirror contour» and
«Mirror contour with reference to a line» of the tab CONTOUR are not applicable to a title.






