Digitizer:Description of Operations with the Digitizer

From Julivi Help
Revision as of 16:06, 25 January 2017 by ArtemReznikov (Talk | contribs) (Created page with "__TOC__ Currently, JULIVI CAD complex program used for pieces archiving supports two types of digitizers: Flatbed Digitizer – input device based on an electromagnetic matr...")

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Contents

Currently, JULIVI CAD complex program used for pieces archiving supports two types of digitizers:

Flatbed Digitizer – input device based on an electromagnetic matrix and a flatbed pointer with buttons.

Optical Digitizer – input device based on electronic paper and electronic pointer for reading the coordinate points from the digitizer surface and information transmission.

These digitizers have different settings and operation principle.

Flatbed Digitizer

Description of Operations with the Flatbed Digitizer

1. Preparation for Archiving

1.1 User Interface of Pieces Archiving Program

1.2 Standard Digitizer Text Panel Commands

1.3 Digitizer Cursor Buttons Layout

2. General Archiving Procedure

3. Piece Archiving

3.1 Archiving a Piece by One Size

3.2 Archiving Pieces Bigger Than the Digitizer Size

4. Specificity of a Piece Graded Nest Archiving

4.1 Archiving a Piece Graded Nest Size by Size

4.2 Archiving a Piece Graded Nest by Two Sizes (with Equal Increment Value between the Sizes)

4.3 Archiving a Piece Graded Nest by Three and More Sizes (with Different Increment Value between the Sizes)

4.4 Archiving a Piece Graded Nest by All Sizes

4.5 Archiving a Piece Graded Nest with Different Increments in One or More Points

Preparation for Archiving

To start archiving a piece:

  • Turn on the digitizer.
  • If there isn't an object (a model) to store the piece into, it shall be created. To create a model, click En arjwin embim26.gifLoad Pieces in the left tool bar.

En arjwin embim27.png

The window for operations with database is displayed.

En arjwin embim28.png

  • In this window, select any model with appropriate size scale and the object name or, simply, any model. Rewrite the object code and, if necessary, rewrite the name, select the designer, select the size scale and click En arjwin embim29.gifCreate New Object.

En arjwin embim30.png

  • Then, in the left lower corner click En arjwin embim31.gifMake Working Object.

In Pieces tab, the list of pieces will be empty.

En arjwin embim32.png

  • Then click Cancel.
  • In PIECE tab, click En arjwin embim33.png. You also may select the following options in the contextual menu: Piece / Enter from Digitizer.

En arjwin embim34.png

  • Pieces Archiving window will be displayed

En arjwin embim35.png

  • Fill in the necessary parameters: material, name, number of cut pieces. Specify the size and height of the piece and the type of entered contour: cut or finished view. If necessary, change the other piece parameters.
  • Click YES. Graded Nest Archivingwindow will be displayed.

The workspace window of digitizer program is displayed. The image on the screen is the copy of the digitizer table.

User Interface of Pieces Archiving Program

1. Pieces archiving program is launched after Piece Archiving command is called in Designer's Workstation program.

2. The program is displayed full screen. The program window includes the following elements:

1. The digitizer active zone.

2. Commands text panel.

3. Archiving process status bar.

4. Archived piece sizes line.

5. Piece area and size line.

6. Comments line for the command text panel.

7. The piece saving process status line.

En arjwin embim36.png

3. During archiving, the piece is displayed by lines of different color and its nodule points and tacks are displayed as different color point.

The following colors of the points and contours are used:

Black point – a point of the initial size piece (small one – intermediate point, big one – reference final point);

Green point (circle) – a point of the next size piece;

Red square – a notch (small one – intermediate notch, big one – reference final notch);

Black contour – the main contour of the piece (cut line or finished piece line) the points input is started from;

Green contour – tack lines inside the piece or auxiliary line (such as a pocket line, gore cut line);

Blue point – a point mark (such as pin hole, buttonhole, etc.);

Bald red point – a piece legend mark or internal point.

4. The status bar is used to display the following messages while archiving a piece:

Grainline Input –grainline input process;

Internal Point Input – input of an internal mark for the piece legend location;

Mode Input – selection of the next step: save a piece or internal contour input;

Internal Contour Input – internal contour lines input process;

Point mark input – tack points input process.

5. In case of a wrong increment point input the following red color message is displayed under the archiving process status bar:

Graded Nest Has Been Already Finished– displayed if extra increment point was entered (for example, when archiving two sizes of a piece, its final point and two increment points instead of one were indicated).

Intermediate Points Are Not Graded– displayed in case of erratic attempt to enter an increment point to an intermediate non-graded point.

Standard Digitizer Text Panel Commands

The commands may be called from the digitizer text panel by two ways:

1. Place the optic pointer intersection on the required command in the text panel (this is to select the operation to be done) and click one of the pointer buttons. This operation may be accompanied by a sound signal.

2. On the screen in the digitizer workspace window, select the required command with the mouse cursor and left click it.

En arjwin embim37.png

Digitizer Cursor Buttons Layout

Depending on the digitizer settings that are specified above, the numbers and layout of the buttons may be different from this diagram.

En arjwin embim38.png

General Archiving Procedure

General archiving procedure is as follows:

1. Grainline drawing.

2. Marking points that form the basic contour (cut or finished view) of a piece.

3. Basic contour closing.

4. Legend point marking.

5. Marking internal lines and points (if any).

6. Piece saving.

Piece Archiving

After preparatory steps, you start the operations to store a piece. You can store either a single size piece or a graded nest of a piece.

Archiving a Piece by One Size

General procedure for archiving a piece by one size:

  • Put a pen at En arjwin embim69.gif icon of the film digitizer. This is the step of selection of the grainline points. The pen shall be held vertically.
  • Specify two extreme points of the grainline of the piece put under the digitizer surface.

En arjwin embim70.png

  • Put a pen at En arjwin embim71.gif icon – selection of the reference final point – and then, indicate the points along the piece cut clockwise.
  • The final reference point En arjwin embim72.gifallows for a broken transition between sections. If you need a smooth transition, use En arjwin embim73.gif icon – intermediate point selection. If several similar points are required to be put one by one, select the respective icon just once and the points will be indicated in series. Remember, to mark a point in the piece, it, first, shall be selected in the button menu of the digitizer.

Having finished the piece contour, indicate a point close to the initial point and, using a pen, select Close Contour command and mark a point for a legend (general information about the piece) on the piece.

En arjwin embim74.png

  • The notches are placed if En arjwin embim75.gifEn arjwin embim76.gifEn arjwin embim77.png buttons are selected depending on the type of the point the notch shall match with. The notches are displayed as red squares of different size.
  • If you need to enter an internal contour, select Internal Contour in the text panel and, just like when digitizing the cut, select the required icon (point type) and mark the points of internal tacks keeping to the clockwise digitizing rule.
  • Then put the pen into the communication port and the piece will be displayed in the archiving window in some time. Information read time depends on your computer capabilities and may last up to 30 seconds.
  • The next step is to check the correctness of the type of points of the stored piece. If any changes to the entered point are required select this point using mouse pointer and right-click on it, then select the necessary point type in the popup menu.
  • To save a piece click Save.

Archiving Pieces Bigger Than the Digitizer Size

When archiving a piece that is out of the digitizer range, Continue Archiving function is used.

The diagram below shows the procedure for entering an oversized piece.

En arjwin embim45.png

Procedure for digitizing of a piece bigger than the digitizer size:

En arjwin embim46.png

  • Enter external piece contour (using buttons 2 and 1) from point 1 to point 2.
  • If the part of the piece between point 1 and 2 contains marks and lines, they shall be set by selecting Internal ContourInput option in the text panel (input method is the same as with external contour).
  • Then, move the piece so that the rest of it appeared in the digitizer sensitivity range, keeping to approximate grainline direction. With the cursor, select Continue Archiving line in the text panel.
  • Start storing the second part of the piece with entering the grainline.
  • Set point 2 where the first part storing was finished using the same button as for finishing the first part of the piece digitizing. The second part contour shall be finished in point 3 as point 1 has been already entered into the computer.
  • Select Close Contour command in the text panel.
  • Select Save command in the text panel.

Specificity of a Piece Graded Nest Archiving

Any piece graded nest may be archived using two methods:

1. Archiving each size individually and then creating a graded nest in Constructor program.

2. Archiving a piece with a graded nest of two and more sizes. In this case, the initial and the final sizes or the initial or adjacent sizes are entered.


Archiving a Piece Graded Nest Size by Size

Entering and storing each size of the same piece separately is the most frequently used method of a graded nest archiving. Below, find the procedure for such graded nest archiving.

1. In PIECE tab, click En arjwin embim88.png. You also may select the following options in the contextual menu: Piece / Enter from Digitizer.

En arjwin embim89.png

2. Pieces Archiving window will be displayed.

En arjwin embim90.png

3. Enter the necessary parameters: material, name, number of cut pieces. Specify the type of the main (entered) piece contour: cut or finished view. If necessary, change the other parameters: Specify the size and the height of the stored piece. Click YES. Graded Nest Archiving window will be displayed.

4. The piece of the necessary size is stored.

5.

6. In Pieces Archiving window, you need to change only the size (the next size of the stored piece). To store the piece click Yes.

7. Store the piece of the necessary size.

8. Save the piece.

9. Repeat steps 6 to 8 depending on the number of the stored pieces.

WARNING! The stored pieces shall contain the same number of elements (internal contours, section, points). Any piece contour is started from the same point and is marked clockwise. You may change an incorrectly entered graded nest in Constructor program. But, to reduce the corrective operations, be very careful when entering the graded nest size by size.

Archiving a Piece Graded Nest by Two Sizes (with Equal Increment Value between the Sizes)

Procedure for pieces graded nest archiving.

1. Enter required parameters in Pieces Archiving window: material, name, number of cut pieces. Specify the type of the main (entered) piece contour: cut or finished view. If necessary, change the other parameters: Specify two sizes and the height of the stored piece.

En arjwin embim91.png

Click YES. Graded Nest Archiving window will be displayed.

I. Fix pieces of the first and the last size in the digitizer field, having matched them in one common point.

II. Enter grainline En arjwin embim92.gif.

III. Put a reference final point En arjwin embim93.gifat two sizes matching place with a button.

IV. Then, the points of the main piece contour are marked clockwise as follows: reference point En arjwin embim94.gif of the initial (the smallest) size – increment point En arjwin embim95.gif (reference point) of the final (the biggest) size. For intermediate En arjwin embim96.gif (non-reference) points, the increment point is not specified. The notches are placed if En arjwin embim97.gifEn arjwin embim98.gifEn arjwin embim99.png buttons are selected depending on the type of the point the notch shall match with. The notches are displayed as red squares of different size.

V. Close the contour by selecting Close Contour command in the text panel.

VI. Place a point mark in the piece using any button.

If necessary, enter internal lines. For this, select Internal Contour Input in the text panel and, keeping to the order described above, enter tacks moving from a smaller size to a bigger size.

  • Put the pen into the communication port and the piece will be displayed in the storing window in some time. Information read time depends on your computer capabilities and may last up to 30 seconds.
  • The next step is to check the correctness of the type of points of the stored piece. If any changes to the entered point are required, select this point using mouse pointer and right-click on it, then select the necessary point type in the popup menu.
  • To save the piece click Save in the text panel.

You may choose any sizes when archiving a graded nest: adjacent sizes, the smallest and the biggest size, etc.

For more accurate graded nest reading, specify the fist and the last size.

En arjwin embim100.png

Archiving a Piece Graded Nest by Three and More Sizes (with Different Increment Value between the Sizes)

The necessity of archiving three sizes of a graded nest arises in case of an abrupt transition from one value to another in the increment between the graded nest sizes.

Example 1: increment of one point of a piece graded nest (42-56) in the first group of sizes 42-48 is 1 cm, and in the second group of sizes 48-56, it is 1.2 cm. If such a graded nest is entered by two sizes, the interval between the entered sizes will be divided into the number of sizes in the graded nest and the increment will be equal to 1.085 cm.

For correct entering of such graded nest, three sizes shall be stored: 42 (the first size in the first group), 48 (the last size in the first group and the first in the second), 56 (the last size in the second group). In such case, the intervals between sizes 42-48 and 48-56 will be divided into the number of the sizes in these groups and the increments in these groups will be equal to 1 cm and 1.2 cm.

Example 2: increment of one point of a piece graded nest (40-50) in the first group of sizes 40-44 is 1 cm, in the second group of sizes 44-48, it is 1.2 cm and in the third group 48-50, it is 1.4 cm.

For correct entering of such graded nest, four sizes shall be stored: 40 (the first size in the first group), 44 (the last size in the first group and the first in the second), 48 (the last size in the second group and the first in the third) and 50 (the last size in the third group). In such case, the intervals between sizes 40-44, 44-48 and 48-50 will be divided into the number of the sizes in these groups and the increments in these groups will be equal to 1 cm, 1.2 cm, and 1.4 cm.

To enter a piece graded nest by three and more sizes, in Pieces Archiving window, select the first, the intermediate and the last sizes of the graded nest in the sizes and height scale.

En arjwin embim101.png

The procedure for archiving a piece graded nest by three and more sizes:

  • Fix pieces of the first, the intermediate and the last size in the digitizer field, having matched them in one common point.
  • Enter grainline En arjwin embim102.gif.
  • Put a reference final point En arjwin embim103.gif at two sizes matching place using a button.

En arjwin embim104.png

  • Then, the points of the main piece contour are marked clockwise as follows: reference point En arjwin embim105.gif of the initial (the smallest) size, increment point – reference point En arjwin embim106.gif of the intermediate size and increment point – reference point En arjwin embim107.gif of the final size. For intermediate En arjwin embim108.gif (non-reference) points, the increment point is not specified. The notches are placed if En arjwin embim109.gifEn arjwin embim110.gifEn arjwin embim111.png buttons are selected depending on the type of the point the notch shall match with. The notches are displayed as red squares of different size.
  • Close the contour by selecting Close Contour command in the text panel.
  • Place a point mark in the piece using any button.
  • If necessary, enter internal tacks. For this, select Internal Contour Input in the text panel and, keeping to the order described above, enter tacks moving from a smaller size to a bigger size.
  • Put the pen into the communication port and the piece will be displayed in the storing window in some time. Information read time depends on your computer capabilities and may last up to 30 seconds.
  • The next step is to check the correctness of the type of points of the stored piece. If any changes to the entered point are required, select this point using mouse pointer and right-click on it, then select the necessary point type in the popup menu.
  • To save the piece click Save in the text panel.

Archiving a Piece Graded Nest by All Sizes

The necessity of archiving all the sizes of a graded nest arises in case the increment between several or all the sizes is different.

To enter the graded nest for all the sizes of the piece, in Pieces Archiving window, select all the sizes of one height in the size scale.

En arjwin embim112.png

Procedure for archiving a piece graded nest of all the sizes:

  • Fix pieces of all the sizes in the digitizer area, having matched them in one common point.
  • Enter grainline En arjwin embim113.png.
  • Put a reference final point En arjwin embim114.png at two sizes matching place using a button.
  • Then, the points of the main piece contour are marked clockwise as follows: reference point En arjwin embim115.png of the initial (the smallest) size, increment point – reference point En arjwin embim116.png of the first intermediate size, then reference point En arjwin embim117.png of the second intermediate size, and so on; and, finally, increment point – reference point En arjwin embim118.png of the final size. For intermediate En arjwin embim119.png (non-reference) points, the increment point is not specified. The notches are placed if En arjwin embim120.pngEn arjwin embim121.pngEn arjwin embim122.png buttons are selected depending on the type of the point the notch shall match with. The notches are displayed as red squares of different size.

En arjwin embim123.png

  • Close the contour by selecting Close Contour command in the text panel.
  • Place a point mark in the piece using any button.
  • If necessary, enter internal tacks. For this, select Internal Contour Input in the text panel and, keeping to the order described above, enter tacks moving from a smaller size to a bigger size.
  • Put the pen into the communication port and the piece will be displayed in the storing window in some time. Information read time depends on your computer capabilities and may last up to 30 seconds.
  • The next step is to check the correctness of the type of points of the stored piece. If any changes to the entered point are required, select this point using mouse pointer and right-click on it, then select the necessary point type in the popup menu.
  • To save the piece click Save in the text panel.

Archiving a Piece Graded Nest with Different Increments in One or More Point

This archiving method is used when there's no need in applying the previous method that requires entering all the graded nest sizes, and one or more points in the piece have different increment values.

Such piece archiving technique is similar to archiving a graded nest by two sizes and to archiving by three and more sizes described above. The difference is that when archiving, points with different increments are entered for each size is series.

Example: 40-50 graded nest, two sizes are stored – 40 and 50, the increment between the sizes will be the same, but in one of the reference points the increment is changed: 40-46 – 1 cm, 46-48 – 1.2 cm, 48-50 – 1.4cm.

The graded nest archiving procedure using this method is as follows:

1. Fix pieces of the first and the last size in the digitizer field, having matched them in one common point.

2. Enter grainline.

3. Put a reference final point at two sizes matching place.

4. Then, the points of the main piece contour are marked clockwise as follows: reference point of the initial (the smallest) size – increment point (reference point) of the final (the biggest) size. For intermediate (non-reference) points, the increment point is not specified. Notches are placed the same way as when archiving a single piece by double click (for increment points – a single click). While archiving a piece graded nest, increment points are displayed in green.

To enter the different value increment point: mark this point as the final reference point in the smallest size, then select Input by Graded Nest option in the text panel and mark points for each size in series clicking grainline and increment points button.

5. Close the contour by selecting Close Contour command in the text panel.

6.

7. If necessary, enter internal tacks. For this, select Internal Contour Input in the text panel and, keeping to the order described above, enter tacks moving from a smaller size to a bigger size.

8. Save a piece by selecting Save command in the text panel.

JULIVI PEN Optical Digitizer

Description of Operations with an Optical Digitizer.

1. Optical Digitizer Description. Basic Principles of a Piece Archiving Using Optical Digitizer

2. Pieces Archiving Preparation

2.1 Creating a Model for a Piece Archiving

2.2 Setting Archived Piece Parameters

2.3 Check for the Digitizer Availability

3. Piece Archiving

3.1 Archiving a Piece by One Size

3.3 Archiving Pieces Bigger Then the Digitizer Size

4. Specificity of a Piece Graded Nest Archiving

4.1 Archiving a Piece Graded Nest Size by Size

4.2 Archiving a Piece Graded Nest by Two Sizes (with Equal Increment Value between the Sizes)

4.3 Archiving a Piece Graded Nest by Three and More Sizes (with Different Increment Value between the Sizes)

4.4 Archiving a Piece Graded Nest by All Sizes

4.5 Archiving a Piece Graded Nest with Different Increments in One or More Points

Optical Digitizer Description. Basic Principles of a Piece Archiving Using Optical Digitizer

Optical digitizer consists of:

Flexible film sheet where coordinate system and functional table microcode is applied;

Electronic optical coordinate reader that is frequently called an Electronic Pen;

A piece archiving using an optical digitizer includes the following steps:

A piece is placed under the digitizer sheet.

Using electronic pen, you mark nodal points of the main contour of the piece and lines inside the piece. The electronic pen is used to select operations during a piece archiving (some operations such as saving, nodal points type change are made using a mouse pointer on your computer display).

The electronic pen is inserted into the communication port and the data are transmitted to Piece Archiving program.

Afterwards, you just correct mistakes made while archiving and saving the piece from your computer display.

Pieces Archiving Preparation

When preparing for a piece archiving, a model (if necessary) is created, model is loaded into the working space, parameters of the stored piece are set and the digitizer is prepared for work.

Creating a Model for a Piece Archiving

In the left panel in Constructor program window, select En arjwin embim56.gifLoad Pieces or select the following menu options: Object – Operations with Database

En arjwin embim57.png

The window for operations with database is displayed.

En arjwin embim58.png

In this window, select the object (model) name from the list, enter the code of a new object (model), select the designer's name from the list and select the sizes scale of a new model; in the sizes scale, select sizes and heights for a new model and the basic size and height. Then click En arjwin embim59.gifCreate New Object.

Then load the created model into the working space of Constructor program and click En arjwin embim60.gifMake Working Object in the let lower corner.

En arjwin embim61.png

If the model, the pieces are to be stored in, was created before, there's no need to create a new model.

Setting Archived Piece Parameters

In PIECE tab, click En arjwin embim62.png. You also may select the following options in the contextual menu: Piece / Enter from Digitizer.

En arjwin embim63.png

Pieces Archiving window will be displayed.

En arjwin embim64.png

Fill in the necessary parameters: material, name, number of cut pieces. Specify the size and height of the stored piece and the type of entered basic contour: cut or finished view. If necessary, change the other piece parameters.

Click YES. Graded Nest Archiving window will be displayed.

The workspace window of digitizer program is displayed. The displayed image size corresponds to the digitizer active zone to scale.

In contrast to the flatbed digitizer, the optical digitizer does not display the stored piece on the screen while archiving therefore you can see the archiving result only after the piece input process is finished. Another difference between the flatbed and the optical digitizer is the absence of buttons responsible for various types of piece contour points input on the latter. Therefore, to change the entered points types, use panels displayed near the digitizer edge at four sides.

En arjwin embim65.png

Button bar of point types selection:

En arjwin embim66.png

En arjwin embim67.png

Check for the Digitizer Availability

Check for the digitizer availability (the LED indicator of the electronic pen shall be lit green). Communication port shall be connected to USB socket of the computer.

If the digitizer is available, the point in the digitizer icon in the left lower part of the screen is colored green, if it is unavailable, the point is red.

En arjwin embim68.png

Piece Archiving

After preparatory steps, you start the operations to store a piece. You can store either a single size piece or a graded nest of a piece.

Archiving a Piece by One Size

General procedure for archiving a piece by one size:

  • Put a pen at En arjwin embim69.gif icon of the film digitizer. This is the step of selection of the grainline points. The pen shall be held vertically.
  • Specify two extreme points of the grainline of the piece put under the digitizer surface.

En arjwin embim70.png

  • Put a pen at En arjwin embim71.gif icon – selection of the reference final point – and then, indicate the points along the piece cut clockwise.
  • The final reference point En arjwin embim72.gifallows for a broken transition between sections. If you need a smooth transition, use En arjwin embim73.gif icon – intermediate point selection. If several similar points are required to be put one by one, select the respective icon just once and the points will be indicated in series. Remember, to mark a point in the piece, it, first, shall be selected in the button menu of the digitizer.

Having finished the piece contour, indicate a point close to the initial point and, using a pen, select Close Contour command and mark a point for a legend (general information about the piece) on the piece.

En arjwin embim74.png

  • The notches are placed if En arjwin embim75.gifEn arjwin embim76.gifEn arjwin embim77.png buttons are selected depending on the type of the point the notch shall match with. The notches are displayed as red squares of different size.
  • If you need to enter an internal contour, select Internal Contour in the text panel and, just like when digitizing the cut, select the required icon (point type) and mark the points of internal tacks keeping to the clockwise digitizing rule.
  • Then put the pen into the communication port and the piece will be displayed in the archiving window in some time. Information read time depends on your computer capabilities and may last up to 30 seconds.
  • The next step is to check the correctness of the type of points of the stored piece. If any changes to the entered point are required select this point using mouse pointer and right-click on it, then select the necessary point type in the popup menu.
  • To save a piece click Save.

Archiving Pieces Bigger Then the Digitizer Size

General procedure for archiving a piece by one size:

  • Put the piece under the sheet surface so that the part of the piece to be stored first is fully covered with the digitizer sheet.
  • Put a pen at En arjwin embim78.gif icon of the film digitizer. This is the step of selection of the grainline points. The pen shall be held vertically.
  • Specify two extreme points of the grainline of the piece put under the digitizer surface.

En arjwin embim79.png

  • Put a pen at En arjwin embim80.gif icon – selection of the reference final point – and then, indicate the points along the piece cut clockwise.
  • The final reference point En arjwin embim81.gifallows for a broken transition between sections. If you need a smooth transition, use En arjwin embim82.gif icon – intermediate point selection. If several similar points are required to be put one by one, select the respective icon just once and the points will be indicated in series. Remember, to mark a point in the piece, it, first, shall be selected in the button menu of the digitizer.
  • The archiving is finished in the point at the end of the first part of the main contour. Upon finishing, select, with the pen, Continue Archiving command in the text menu.

En arjwin embim83.png

  • You need to place a piece so that the rest of it was fully covered by the digitizer sheet.
  • Start storing the second part of the piece with entering the grainline.
  • Set point for the beginning of archiving of the second part (it coincides with the point where the first part archiving was finished) using the same button as for finishing the first part of the piece digitizing. The second part contour shall be finished in the point slightly distanced from the initial contour point.

En arjwin embim84.png

  • Select Close Contour command in the text panel.
  • The notches are placed if En arjwin embim85.gifEn arjwin embim86.gifEn arjwin embim87.png buttons are selected depending on the type of the point the notch shall match with. The notches are displayed as red squares of different size.
  • If you need to enter an internal contour, select Internal Contour in the text panel and, just like when digitizing the cut, select the required icon (point type) and mark the points of internal tacks keeping to the clockwise digitizing rule.
  • Then put the pen into the communication port and the piece will be displayed in the archiving window in some time. Information read time depends on your computer capabilities and may last up to 30 seconds.
  • The next step is to check the correctness of the type of points of the stored piece. If any changes to the entered point are required select this point using mouse pointer and right-click on it, then select the necessary point type in the popup menu.
  • To save the piece click Save in the text panel.

Specificity of a Piece Graded Nest Archiving

Any piece graded nest may be archived using two methods:

1. Archiving each size individually and then creating a graded nest in Constructor program.

2. Archiving a piece with a graded nest of two and more sizes. In this case, the initial and the final sizes or the initial or adjacent sizes are entered.

Archiving a Piece Graded Nest Size by Size

Entering and storing each size of the same piece separately is the most frequently used method of a graded nest archiving. Below, find the procedure for such graded nest archiving.

1. In PIECE tab, click En arjwin embim88.png. You also may select the following options in the contextual menu: Piece / Enter from Digitizer.

En arjwin embim89.png

2. Pieces Archiving window will be displayed.

En arjwin embim90.png

3. Enter the necessary parameters: material, name, number of cut pieces. Specify the type of the main (entered) piece contour: cut or finished view. If necessary, change the other parameters: Specify the size and the height of the stored piece. Click YES. Graded Nest Archiving window will be displayed.

4. The piece of the necessary size is stored.

5.

6. In Pieces Archiving window, you need to change only the size (the next size of the stored piece). To store the piece click Yes.

7. Store the piece of the necessary size.

8. Save the piece.

9. Repeat steps 6 to 8 depending on the number of the stored pieces.

WARNING! The stored pieces shall contain the same number of elements (internal contours, section, points). Any piece contour is started from the same point and is marked clockwise. You may change an incorrectly entered graded nest in Constructor program. But, to reduce the corrective operations, be very careful when entering the graded nest size by size.

Archiving a Piece Graded Nest by Two Sizes (with Equal Increment Value between the Sizes)

Procedure for pieces graded nest archiving.

1. Enter required parameters in Pieces Archiving window: material, name, number of cut pieces. Specify the type of the main (entered) piece contour: cut or finished view. If necessary, change the other parameters: Specify two sizes and the height of the stored piece.

En arjwin embim91.png

Click YES. Graded Nest Archiving window will be displayed.

I. Fix pieces of the first and the last size in the digitizer field, having matched them in one common point.

II. Enter grainline En arjwin embim92.gif.

III. Put a reference final point En arjwin embim93.gifat two sizes matching place with a button.

IV. Then, the points of the main piece contour are marked clockwise as follows: reference point En arjwin embim94.gif of the initial (the smallest) size – increment point En arjwin embim95.gif (reference point) of the final (the biggest) size. For intermediate En arjwin embim96.gif (non-reference) points, the increment point is not specified. The notches are placed if En arjwin embim97.gifEn arjwin embim98.gifEn arjwin embim99.png buttons are selected depending on the type of the point the notch shall match with. The notches are displayed as red squares of different size.

V. Close the contour by selecting Close Contour command in the text panel.

VI. Place a point mark in the piece using any button.

If necessary, enter internal lines. For this, select Internal Contour Input in the text panel and, keeping to the order described above, enter tacks moving from a smaller size to a bigger size.

  • Put the pen into the communication port and the piece will be displayed in the storing window in some time. Information read time depends on your computer capabilities and may last up to 30 seconds.
  • The next step is to check the correctness of the type of points of the stored piece. If any changes to the entered point are required, select this point using mouse pointer and right-click on it, then select the necessary point type in the popup menu.
  • To save the piece click Save in the text panel.

You may choose any sizes when archiving a graded nest: adjacent sizes, the smallest and the biggest size, etc.

For more accurate graded nest reading, specify the fist and the last size.

En arjwin embim100.png

Archiving a Piece Graded Nest by Three and More Sizes (with Different Increment Value between the Sizes)

The necessity of archiving three sizes of a graded nest arises in case of an abrupt transition from one value to another in the increment between the graded nest sizes.

Example 1: increment of one point of a piece graded nest (42-56) in the first group of sizes 42-48 is 1 cm, and in the second group of sizes 48-56, it is 1.2 cm. If such a graded nest is entered by two sizes, the interval between the entered sizes will be divided into the number of sizes in the graded nest and the increment will be equal to 1.085 cm.

For correct entering of such graded nest, three sizes shall be stored: 42 (the first size in the first group), 48 (the last size in the first group and the first in the second), 56 (the last size in the second group). In such case, the intervals between sizes 42-48 and 48-56 will be divided into the number of the sizes in these groups and the increments in these groups will be equal to 1 cm and 1.2 cm.

Example 2: increment of one point of a piece graded nest (40-50) in the first group of sizes 40-44 is 1 cm, in the second group of sizes 44-48, it is 1.2 cm and in the third group 48-50, it is 1.4 cm.

For correct entering of such graded nest, four sizes shall be stored: 40 (the first size in the first group), 44 (the last size in the first group and the first in the second), 48 (the last size in the second group and the first in the third) and 50 (the last size in the third group). In such case, the intervals between sizes 40-44, 44-48 and 48-50 will be divided into the number of the sizes in these groups and the increments in these groups will be equal to 1 cm, 1.2 cm, and 1.4 cm.

To enter a piece graded nest by three and more sizes, in Pieces Archiving window, select the first, the intermediate and the last sizes of the graded nest in the sizes and height scale.

En arjwin embim101.png

The procedure for archiving a piece graded nest by three and more sizes:

  • Fix pieces of the first, the intermediate and the last size in the digitizer field, having matched them in one common point.
  • Enter grainline En arjwin embim102.gif.
  • Put a reference final point En arjwin embim103.gif at two sizes matching place using a button.

En arjwin embim104.png

  • Then, the points of the main piece contour are marked clockwise as follows: reference point En arjwin embim105.gif of the initial (the smallest) size, increment point – reference point En arjwin embim106.gif of the intermediate size and increment point – reference point En arjwin embim107.gif of the final size. For intermediate En arjwin embim108.gif (non-reference) points, the increment point is not specified. The notches are placed if En arjwin embim109.gifEn arjwin embim110.gifEn arjwin embim111.png buttons are selected depending on the type of the point the notch shall match with. The notches are displayed as red squares of different size.
  • Close the contour by selecting Close Contour command in the text panel.
  • Place a point mark in the piece using any button.
  • If necessary, enter internal tacks. For this, select Internal Contour Input in the text panel and, keeping to the order described above, enter tacks moving from a smaller size to a bigger size.
  • Put the pen into the communication port and the piece will be displayed in the storing window in some time. Information read time depends on your computer capabilities and may last up to 30 seconds.
  • The next step is to check the correctness of the type of points of the stored piece. If any changes to the entered point are required, select this point using mouse pointer and right-click on it, then select the necessary point type in the popup menu.
  • To save the piece click Save in the text panel.

Archiving a Piece Graded Nest by All Sizes

The necessity of archiving all the sizes of a graded nest arises in case the increment between several or all the sizes is different.

To enter the graded nest for all the sizes of the piece, in Pieces Archiving window, select all the sizes of one height in the size scale.

En arjwin embim112.png

Procedure for archiving a piece graded nest of all the sizes:

  • Fix pieces of all the sizes in the digitizer area, having matched them in one common point.
  • Enter grainline En arjwin embim113.png.
  • Put a reference final point En arjwin embim114.png at two sizes matching place using a button.
  • Then, the points of the main piece contour are marked clockwise as follows: reference point En arjwin embim115.png of the initial (the smallest) size, increment point – reference point En arjwin embim116.png of the first intermediate size, then reference point En arjwin embim117.png of the second intermediate size, and so on; and, finally, increment point – reference point En arjwin embim118.png of the final size. For intermediate En arjwin embim119.png (non-reference) points, the increment point is not specified. The notches are placed if En arjwin embim120.pngEn arjwin embim121.pngEn arjwin embim122.png buttons are selected depending on the type of the point the notch shall match with. The notches are displayed as red squares of different size.

En arjwin embim123.png

  • Close the contour by selecting Close Contour command in the text panel.
  • Place a point mark in the piece using any button.
  • If necessary, enter internal tacks. For this, select Internal Contour Input in the text panel and, keeping to the order described above, enter tacks moving from a smaller size to a bigger size.
  • Put the pen into the communication port and the piece will be displayed in the storing window in some time. Information read time depends on your computer capabilities and may last up to 30 seconds.
  • The next step is to check the correctness of the type of points of the stored piece. If any changes to the entered point are required, select this point using mouse pointer and right-click on it, then select the necessary point type in the popup menu.
  • To save the piece click Save in the text panel.

Archiving a Piece Graded Nest with Different Increments in One or More Points

This archiving method is used when there's no need in applying the previous method that requires entering all the graded nest sizes, and one or more points in the piece have different increment values.

Such piece archiving technique is similar to archiving a graded nest by two sizes and to archiving by three and more sizes described above. The difference is that when storing, points with different increments are entered for each size is series.

Example: 40-50 graded nest, two sizes are stored – 40 and 50, the increment between the sizes will be the same, but in one of the reference points the increment is changed: 40-46 – 1 cm, 46-48 – 1.2 cm, 48-50 – 1.4cm.

The graded nest archiving procedure using this method is as follows:

  • Fix pieces of the first and the last size in the digitizer field, having matched them in one common point.
  • Enter grainline En arjwin embim124.png.
  • Put a reference final point En arjwin embim125.png at two sizes matching place.
  • Then, the points of the main piece contour are marked clockwise as follows: reference point En arjwin embim126.png of the initial (the smallest) size – increment point En arjwin embim127.png (reference point) of the final (the biggest) size. For intermediate En arjwin embim128.png (non-reference) points, the increment point is not specified. The notches are placed if En arjwin embim129.pngEn arjwin embim130.pngEn arjwin embim131.png buttons are selected depending on the type of the point the notch shall match with. The notches are displayed as red squares of different size.

En arjwin embim132.png

  • To enter the different value increment point: mark this point as the final reference point En arjwin embim133.png in the smallest size, then select Input by Graded Nest option in the text panel and mark points for each size in series clicking grainline and increment points En arjwin embim134.png button.
  • Close the contour by selecting Close Contour command in the text panel.
  • Place a point mark in the piece using any button.
  • If necessary, enter internal tacks. For this, select Internal Contour Input in the text panel and, keeping to the order described above, enter tacks moving from a smaller size to a bigger size.
  • Put the pen into the communication port and the piece will be displayed in the storing window in some time. Information read time depends on your computer capabilities and may last up to 30 seconds.
  • The next step is to check the correctness of the type of points of the stored piece. If any changes to the entered point are required, select this point using mouse pointer and right-click on it, then select the necessary point type in the popup menu.
  • To save the piece click Save in the text panel.