Constructor:Lines

From Julivi Help
Revision as of 13:38, 5 March 2015 by Roman (Talk | contribs) (→‎Straight line set from a point at distance)

Jump to: navigation, search

Lines

For making different marks or auxiliary constructions you may often need to draw different types of lines (horizontal, vertical, straight, parallel, etc) on pieces.

These lines are drafted on the piece as inner contours with the help of the commands in the LINES tab or from the text menu "Contour/ Lines": 1.png

You can make the following constructions: Horizontal line, Vertical line, Normal and Tangent lines, Equidistant line, Segment of a set length and direction; Straight line between points; Quilting lines.

Straight lines

Straight line from a point

To create a straight line of a set type (horizontal, vertical, normal, tangent) from any point of the section:

  • Select the LINES tab and the button 3.png in this tab. The cursor view is changed to 4.png.

You can also follow the text menu points "Contour/ Lines / Straight line from a point".

  • Specify the point (1) or any place of the section. The window with the parameters of the straight line is displayed on the screen:

2.png

  • Limitation for a straight line inside the contour, where a point is specified, is set by default

If necessary, you can select a different type of a limiting contour by means of switching on a necessary type of the switch “Limit”. It can be Cut, Finished view or any locked contour specified upon selection of a point: Inner or Working contour.

  • Select the button of a necessary construction command with clicking it with the left mouse button:

3.png-horizontal 5.png-vertical 6.png-normal 7.png-tangent.

8.png

ADDITIONAL

MODE Construction of “Normal” and “Tangent” from the End point of a section

To construct “Normal” and “Tangent” from the end point to one of the two adjacent sections of this point, you need to specify, which section will be used. It means that the function must be performed in a special mode:

  • Press and hold the <CTRL> key on the keyboard after selection of the function
  • Specify not the End point (1) on the screen, but a spot on the section next to it, by means of selection of one of the sections for construction of a normal or a tangent line.
  • Release the <CTRL> key at the time of display of the window for input of values or setting the type of a line.

9.png

FEATURES

  1. When constructing lines from the Inner contour, Sight, or Pinhole, contour limitation is performed up to the main contour by default.
  2. When "Normal"is constructed from the End point, the straight line goes through an angle bisector between the adjacent sections. The construction "Tangent" from an End point has no sense
  3. If there are several crossing places of a straight line and the limiting contour, a line consisting of several sections is created. It is possible to create a different number of sections in different sizes of a graded piece, so it is recommended to check all sizes. 10.png
  4. You can work with a group of superposed pieces (the commands 11.png of the screen menu).

A straight line will be created separately on each piece.

Straight line set from a point at distance

To construct a straight line of a set type (horizontal, vertical, normal, tangent) at distance from a specified point on the contour:

  • Select the LINES tab and the button 12.png in this tab. The cursor view is changed to 4.png. You can also follow the text menu points "Contour/ Lines / Straight line set from a point at distance".
  • Specify the point (1) from which distance will be measured. The window for input of data is displayed on the screen:

13.png

  • Input an indention value from the point along the contour curve. The sign of the input value is defined according to the rule of positive contour outline (clockwise–"plus", counter-clockwise–"minus").
  • Press the YES button. The window for selection of construction type is displayed on the screen:

2.png

  • Limitation of a straight line inside the contour, where a point is specified, is set by default.

If necessary, you can select another type of a limiting contour, by means of switching on the required type of the switch "Limit".

  • Select the button for the type of a line: -horizontal -vertical -normal -tangent

The specifics of the function and description of an additional mode is similar to the function "Straight line from a point".