Constructor:Measurement and Calculation Methods

From Julivi Help
Revision as of 12:59, 18 May 2015 by Pavel.Gordon (Talk | contribs) (→‎Checking Ratio and Adjusting Section Lengths in Pairs)

Jump to: navigation, search

Checking Ratio and Adjusting Lengths of Sections

In order to check the lengths of different sections, the length of one section needs to be measured with the “+” sign and the other – with the “-” sign. Than points of one of the pieces are displaced by the amount of the obtained difference, both lengths are equaled. For example, let us check the ratio of the back princess seam lengths:

  • Select embim2460.png command of the section measurement (embim2461.png sign is selected by default).
  • Specify the first section to be measured (1).
  • Change the measurement sign by selecting embim2462.png button.
  • Specify the second section to be measured (2).
embim2463.png
* Select embim2464.png command of the measurement panel to view the difference between the sections for sizes. The difference values are displayed in the “A” tab of the result table.
embim2465.png
            Having analyzed the measurement result, you can adjust the section lengths:
  • Selectembim2466.png command to save the length ratio in the buffer
  • Select one of the point displacement functions. For example, embim2467.png - “Point/ Displace along X”.

·         Select the area around the required point and input the displacement value in the function box.

      To do this, values need to be read from the buffer (embim2469.png) or the size table (embim2469.png) should be opened.

embim2470.png

 The data table in the “F” tab will be opened (the data of the last buffer saved).

  • Specify the direction of the point displacement. If necessary, change the value sign embim2471.png.

In this example, we select the point for displacement: the lower point of the side section on the princess seam.

We specify the displacement sign relative to it and analyze the result in the basic size (88/170):

The length of the side section has been subtracted from the length of the center back section. A positive value (0.17) has been obtained which means that the back section is longer than the side . Therefore, in order to equal these sections, you can extend the  side section by displacing its lower point to the right. In this function the point displacement sign is determined by the direction of the axes (“+” – to the right). The analyzed value (0.17) is positive, so you do not have to change the sign of the values in the tab.

embim2472.png
  • Press the “YES” button to confirm the input of the displacing values. The selected point will be displaced.
  • In order to check the displacement performed, select embim2473.png button of the measurement panel.

A new, recalculated result of the earlier measurement (without a repeated measurement) will be displayed.

  • If the displacement direction has been determined incorrectly, you can cancel it (rollback embim2474.png or embim2475.png in the program screen menu) and repeat the command having changed the displacement direction.
NOTE

 

                                         When another displacement point is selected, the analysis will be different.

For example, select a point for displacement: the lower point of the back section.

We specify the displacement sign relative to it and analyze the result in the basic size (88/170):

The length of the side section has been subtracted from the length of the back section. A positive value (0.17) has been obtained which means that the back section is longer than the side. Therefore, in order to equal these sections, you need to shorten the back section by displacing its lower point to the left.

In this function the point displacement sign is determined by the direction of the axes (“-” – to the left). The analyzed value (0.17) is positive, so its sign needs to be changed (embim2477.png button). Negative values in the table will become positive, but if you make a similar analysis for these sizes, it will become clear that it is correct.

 

ATTENTION!  If the situation arises when the difference has positive and negative value for sizes, the sign is determined based on one of the sizes (any one).

Checking Ratio and Adjusting Section Lengths in Pairs

 

     Let us consider the same example with the princess seam measuring but involving notch adjustment. You can measure the distance between the relevant notches and adjust each distance individually. Besides, the program allows pairwise measurement of the entire section length based on the notches.

     In order to measure sections in pairs:

·         Select the section part measuring command embim2478.png (embim2479.png sign is selected by default).

·         Specify two points of the first measurement section: 1а and 2а

·         Change the sign to embim2480.png. Specify two relevant points of the second section: 1b and 2b.

·         Change the sign to embim2481.png. Specify the following points of the first section: 2а and 3а.

·         Change the sign to embim2482.png. Specify the relevant points of the second section: 2b and 3b.

·         Change the sign to embim2483.png. Specify the points of the first section: 3а and 4а.

·         Change the sign to embim2484.png. Specify the points of the second section: 3b and 4b.

·         The remaining parts of the section need to be specified in the same sequence.

ATTENTION! When measuring pairwise, it is essential to follow the sequence: all parts of one piece with the “+” sign and the corresponding parts of the second piece – with the “-” sign.  

embim2485.png
  • Select embim2486.png command of the lower panel to display the table of results for all sizes.

      The total difference for the length of the entire section will be displayed in the table.

embim2487.png
  • You can select any of the measured pairs in the pair list box embim2488.png to view the data:

      embim2489.png – the total difference of lengths of all pairs 

embim2490.png – the difference between the sections of the first pair 1а-2а and 1b-2b,

embim2491.png – the difference between the sections of the second pair 2a-3a and 2b-3b, etc.

embim2492.png
  • Select embim2493.png item (total difference) in the pair list to adjust the total length of the section.

After the data have been saved in the bufferembim2494.png, select one of the functions in the POINT tab ( embim2495.png,…) for  operating the Terminal points of the section and displace the end of the section by this amount (from the buffer embim2496.png)

·         Adjust the lengths between notches:

1) Select the first measured pair in the pair list  embim2497.png. The measurement result will be displayed in the table.

2) Save the table data in the buffer embim2498.png

3) Select the command for displacement of the Intermediate points embim2499.png - “Point/ Displace along curve by…”.

4) Specify the notch to be displaced (2a or 2b) and retrieve data from the buffer in the function box embim2500.png.

5) Specify the direction of the point movement (around the outline clockwise – “+”: counterclockwise – “-”).

6) Perform the displacement and select embim2501.png command of the measurement panel for recalculation.

7) Select this pair from the pair list embim2502.png in the table to check the result for it.  

  • Make similar adjustment between notches on all other parts of the section.

 

NOTE

 

    1) When the lengths of sections are adjusted, the function of the point displacement is selected depending on the point type: Terminal or Intermediate point.

2)      The pair box is displayed in the Result Table only after at least one pair has been created (“+” and “-”)

3)      Be sure to start measuring pairs with the “+” sign, otherwise, the pair box will not be displayed.

4)      Making expressions with the measurement result (the “A” tab) when performing functions is possible for the total result only, not for individual pairs.


 

embim2504.png

Setting a required fitting value on a section