Constructor:Measurement and Calculation Methods

From Julivi Help
Revision as of 12:32, 18 May 2015 by Pavel.Gordon (Talk | contribs) (→‎Checking Ratio and Adjusting Lengths of Sections)

Jump to: navigation, search

Checking Ratio and Adjusting Lengths of Sections

In order to check the lengths of different sections, the length of one section needs to be measured with the “+” sign and the other – with the “-” sign. Than points of one of the pieces are displaced by the amount of the obtained difference, both lengths are equaled. For example, let us check the ratio of the back princess seam lengths:

  • Select embim2460.png command of the section measurement (embim2461.png sign is selected by default).
  • Specify the first section to be measured (1).
  • Change the measurement sign by selecting embim2462.png button.
  • Specify the second section to be measured (2).
embim2463.png
* Select embim2464.png command of the measurement panel to view the difference between the sections for sizes. The difference values are displayed in the “A” tab of the result table.
embim2465.png
            Having analyzed the measurement result, you can adjust the section lengths:
  • Selectembim2466.png command to save the length ratio in the buffer
  • Select one of the point displacement functions. For example, embim2467.png - “Point/ Displace along X”.

·         Select the area around the required point and input the displacement value in the function box.

      To do this, values need to be read from the buffer (embim2469.png) or the size table (embim2469.png) should be opened.

embim2470.png

 The data table in the “F” tab will be opened (the data of the last buffer saved).

  • Specify the direction of the point displacement. If necessary, change the value sign embim2471.png.

In this example, we select the point for displacement: the lower point of the side section on the princess seam.

We specify the displacement sign relative to it and analyze the result in the basic size (88/170):

The length of the side section has been subtracted from the length of the center back section. A positive value (0.17) has been obtained which means that the back section is longer than the side . Therefore, in order to equal these sections, you can extend the  side section by displacing its lower point to the right. In this function the point displacement sign is determined by the direction of the axes (“+” – to the right). The analyzed value (0.17) is positive, so you do not have to change the sign of the values in the tab.

embim2472.png
  • Press the “YES” button to confirm the input of the displacing values. The selected point will be displaced.
  • In order to check the displacement performed, select embim2473.png button of the measurement panel.

A new, recalculated result of the earlier measurement (without a repeated measurement) will be displayed.

  • If the displacement direction has been determined incorrectly, you can cancel it (rollback embim2474.png or embim2475.png in the program screen menu) and repeat the command having changed the displacement direction.
NOTE

 

                                         When another displacement point is selected, the analysis will be different.

For example, select a point for displacement: the lower point of the back section.

We specify the displacement sign relative to it and analyze the result in the basic size (88/170):

The length of the side section has been subtracted from the length of the back section. A positive value (0.17) has been obtained which means that the back section is longer than the side. Therefore, in order to equal these sections, you need to shorten the back section by displacing its lower point to the left.

In this function the point displacement sign is determined by the direction of the axes (“-” – to the left). The analyzed value (0.17) is positive, so its sign needs to be changed (embim2477.png button). Negative values in the table will become positive, but if you make a similar analysis for these sizes, it will become clear that it is correct.

 

ATTENTION!  If the situation arises when the difference has positive and negative value for sizes, the sign is determined based on one of the sizes (any one).

Checking ratio and correcting section lengths in pairs

Setting a required fitting value on a section