Difference between revisions of "Constructor:Contour parameters"
(Blanked the page) |
|||
| Line 1: | Line 1: | ||
| + | It is possible to change contour parameters working with pieces. Contour properties change in this case. | ||
| + | For example, for the '''Inner''' contour line to be drafted in the layout, its parameters must be changed to a '''Sight''' type. To change contour parameters: | ||
| + | ·Select tab CONTOUR and the button [[File:embim1599.png]] in this tab. The cursor view changes to [[File:embim1600.png]] | ||
| + | It is also possible to follow text menu points «Contour/ Parameters». | ||
| + | ·Specify a contour being changed. The window of contour parameters is displayed on the screen: | ||
| + | [[File:embim1601.png]] | ||
| + | |||
| + | A selected option [[File:embim1602.png]] next to a contour signifies, which contour type was selected. Contour types listed in black color are active (a specified contour can be replaced with them). Contour types listed in grey color are inactive, blocked for contour replacement. | ||
| + | View of the window «Contour parameters» changes depending on what type of contour was specified. | ||
| + | ·Select a required type of contour by selecting the option [[File:embim1602.png]] nest to a required contour type. | ||
| + | ·Press the YES button to confirm data input, press CANCEL to cancel. | ||
| + | |||
| + | It is possible to change line view (Lines, Crosses, Do not draw) for layouts and construction drafts when specifying '''Inner''' and '''Sight''' contours in an additional window, and select setting for drafting or cutting contour applicable to the cutting plotter. | ||
| + | When contour '''Pinhole''' is specified, additional setting of punch number is displayed | ||
| + | |||
| + | [[File:embim1604.png]] | ||
| + | |||
| + | When contours Working and Finished view are specified, an option [[File:embim1605.png]] is displayed. | ||
| + | This option is blocked for the contour Working, since this contour can only be used as main. Finished view can be main and derived contour (if Working contour is set as main). | ||
| + | |||
| + | [[File:embim1606.png]] 1) A piece cannot exist without the main contour. When trying to rename the main contour, the following message is displayed: | ||
| + | |||
| + | [[File:embim1607.png]] | ||
| + | |||
| + | 2) When contours are renamed in pieces with incorrect graded nest, a warning is displayed: | ||
| + | |||
| + | [[File:embim1608.png]] | ||
| + | |||
| + | 3) '''ATTENTION!''' SYMMETRY status is removed upon any renaming of the Cut contour or the main contour. | ||
| + | 4) When two similar contours configurations fully match the program uses one of them for work (specifically in the tab CONTOUR). Also, 2 functions o the tab SECTION will apply – «Delete section» ([[File:embim1609.png]]) and «Move section» ([[File:embim1610.png]]) in the mode «Without deformation». | ||
Latest revision as of 11:05, 5 March 2015
It is possible to change contour parameters working with pieces. Contour properties change in this case.
For example, for the Inner contour line to be drafted in the layout, its parameters must be changed to a Sight type. To change contour parameters:
·Select tab CONTOUR and the button
in this tab. The cursor view changes to
It is also possible to follow text menu points «Contour/ Parameters».
·Specify a contour being changed. The window of contour parameters is displayed on the screen:
A selected option
next to a contour signifies, which contour type was selected. Contour types listed in black color are active (a specified contour can be replaced with them). Contour types listed in grey color are inactive, blocked for contour replacement.
View of the window «Contour parameters» changes depending on what type of contour was specified.
·Select a required type of contour by selecting the option
nest to a required contour type.
·Press the YES button to confirm data input, press CANCEL to cancel.
It is possible to change line view (Lines, Crosses, Do not draw) for layouts and construction drafts when specifying Inner and Sight contours in an additional window, and select setting for drafting or cutting contour applicable to the cutting plotter. When contour Pinhole is specified, additional setting of punch number is displayed
When contours Working and Finished view are specified, an option
is displayed.
This option is blocked for the contour Working, since this contour can only be used as main. Finished view can be main and derived contour (if Working contour is set as main).
1) A piece cannot exist without the main contour. When trying to rename the main contour, the following message is displayed:
2) When contours are renamed in pieces with incorrect graded nest, a warning is displayed:
3) ATTENTION! SYMMETRY status is removed upon any renaming of the Cut contour or the main contour.
4) When two similar contours configurations fully match the program uses one of them for work (specifically in the tab CONTOUR). Also, 2 functions o the tab SECTION will apply – «Delete section» (
) and «Move section» (
) in the mode «Without deformation».



