Difference between revisions of "Constructor:Results of calculations of the «Seam algebra»"
(Created page with "== Results of calculations done in the “Seam algebra” == To display measurement results for all sizes, select the command Image:embim2368.png - “Result for the wh...") |
(No difference)
|
Revision as of 23:21, 3 March 2015
Results of calculations done in the “Seam algebra”
To display measurement results for all sizes, select the command
- “Result for the whole graded piece” on the measurement panel. The table is displayed in two working modes:
- results of calculations done in the “Seam algebra”;
- “Calculator”
Upon selection of the command
, a table opened in the window for the “Seam algebra” results
is displayed.

In this mode, the table has several tabs:
- result of calculation. The sum or difference of the measured lengths is displayed in the cells
Upon clicking the area with the table values with the right mouse button, an additional menu with a highlighted active mode is displayed. Selection of the menu points is done with clicking a line:

Do not display expression – output of result, without summands
Sum of positive values – output of sum of positive values and result
Sum of negative values – output of sum of negative values and result.
Whole expression – output of a negative and positive value, as well as the result
(Expression is displayed for one size, which cell was specified with a click of the right mouse button.)

- sum of positive values. Measurements done with a plus sign (the button
).
- sum of negative values. Measurements done with a minus sign (the button
).

When clicking any cell in the tab with the right mouse button, an additional menu is displayed:
'Divide by sum of positive values – coefficient is calculated by dividing tabs “А'”/ “'В'”
'Divide by sum of negative values - coefficient is calculated by dividing tabs “А'”/ “'С'”.

If multiply the value in the tab by 100, you get FITTING PERCENTAGE.
The tab is displayed on the yellow background since it contains coefficients instead of linear values.
- difference from the basic (size, height, size and height).
Upon clicking any cell of the tab with the right mouse button, an additional menu is displayed

From the basic size and height – calculation of difference for each size from the basic size and height
From the basic size – calculation of difference for each size from the basic size
From the basic height – calculation of difference for each size from the basic height
When the piece elements are moved by the difference value, the result of measurement for sizes will be the same as that for the basic size. For example, when moving a point by the value of difference between other sizes and the basic size, you can get fitting for the section in all sizes the same as in the standard, basic size.

'Size increments – output of the increment value (difference between sizes in the tab “А'”)

This increment value can be used in the Increment table
, by opening it from the buffer
Functions of the table with the calculation results
(or an additional menu point
) – save the table data to file, to store and transfer electronic information. A tab opened at the time of
saving the table is saved.
(an additional menu point) – send to print of the data from the opened tab of the table.
- window for selection of pairs (for paired measurement of sections with alternation of groups “+” and “-“)
- window for input of values and expressions with tabs A,B,C,D,E (For example, “A+2”)
ATTENTION! When making expressions, nonlinear values (coefficients) should be taken in square brackets. For example, when multiplying “'А'*[2]” and dividing “A/[2]”.
- calculation of the expression result. The result is displayed in the tab
of the “Calculator”
window.
Then this data is used in different functions of the program upon input of values.

(or an additional menu point
) – record of the table data to the buffer.
At the same time the tab
of the “Calculator”
window is filled in. This tab is always automatically filled in with the data of the last saved buffer.
While performing different functions, or during input of movement, rotation values etc, you can open the size table (
), or the data from the buffer(
). The tab “F” will be opened.
Standard work method: To use the measurement results while performing the functions, the tab “'А'” saved in the buffer
should be read from the buffer
.

To use measurement results while performing the functions, apart from work with the buffer, you can input the name of the tab “A” (in English), or
any other tab, in the input window without clearing the measurement window and opening the size table(
or
). This work mode is very convenient.
Besides, it is mandatory for further performance of the command “Reconstruction”.

FEATURES
1)If a piece with an incomplete gradation is displayed on the screen, during calculations between this piece and a full piece, the result table with
blank cells for missing sizes and a list of missing sizes are displayed.

2) While addressing measurements of the pieces deleted from the screen or changed by rollback (with deletion of the measured element), etc, a message about an error made in the expression calculation is displayed.
When such a message is displayed, the measurement window of the “Seam algebra” must be cleared with selection of the command

3) The parameters for output of the measurement results displayed as “switched on” by default in an additional floating menu of the table, are selected in the settings and can be changed (the menu points “Settings/ Program parameters”,SEAM ALGEBRA tab):

4) The floating hints for the tabs A, B, C, D, E are displayed when placing the cursor not next to, but below the tab names

5) When making expressions with the tab “'А'” while performing the function, there is an important special feature:
If after measuring a section (result – tab “А'”) you perform the command for moving points changing the length of the measured sections, the value “А'” will be different (recalculated) after the first change of the length of the given section.
For example: you need to set shoulder fitting 0,25cm on the section, by means of deformation of both measured sections: shorten the forepart shoulder and extend the back shoulder.
If you make an expression “'А'-0.25/[2]”, it will only be correct for the first of the sections being deformed. Because while working with this expression on the second section, the variable “'А'” will have a new value changed upon the first movement. In this case, to move the second section, you have to input the expression “А'-0.25”, or measure a new value of “А'”, and perform the second action of the function with this new value.
