Difference between revisions of "Constructor:Measurement and Calculation Methods"
(Created page with "== Checking ratios and correcting length of sections == == Checking ratio and correcting section lengths in pairs == == Setting a required fitting value on a section == Cate...") |
Pavel.Gordon (Talk | contribs) (→Checking ratios and correcting length of sections) |
||
| Line 1: | Line 1: | ||
| − | == Checking | + | == Checking Ratio and Adjusting Lengths of Sections == |
| + | |||
| + | In order to check the lengths of different sections, the length of one section needs to be measured with the “+” sign and the other – with the “-” sign. Than points of one of the pieces are displaced by the amount of the obtained difference, both lengths are equaled. For example, let us check the ratio of the back princess seam lengths: | ||
| + | |||
| + | * Select [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image002.jpg]] command of the section measurement ([[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image004.jpg]] sign is selected by default). | ||
| + | * Specify the first section to be measured ('''1'''). | ||
| + | * Change the measurement sign by selecting [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image006.jpg]] button. | ||
| + | * Specify the second section to be measured ('''2'''). | ||
| + | |||
| + | [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image008.jpg]]* Select [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image010.jpg]] command of the measurement panel to view the difference between the sections for sizes. The difference values are displayed in the “A” tab of the result table. | ||
| + | |||
| + | [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image012.jpg]] Having analyzed the measurement result, you can <u>adjust the section lengths</u>: | ||
| + | |||
| + | * Select[[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image014.jpg]] command to save the length ratio in the buffer | ||
| + | * Select one of the point displacement functions. For example, [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image015.gif]] - “Point/ Displace along X”. | ||
| + | |||
| + | · Select the area around the required point and input the displacement value in the function box. | ||
| + | |||
| + | To do this, values need to be read from the buffer ([[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image017.jpg]]) or the size table ([[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image019.jpg]]) should be opened. | ||
| + | |||
| + | |||
| + | The data table in the “'''F'''” tab will be opened (the data of the last buffer saved). | ||
| + | |||
| + | * Specify the direction of the point displacement. If necessary, change the value sign [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image023.jpg]]. | ||
| + | |||
| + | In this example, we select the point for displacement: ''the lower point of the side section on the princess seam. '' | ||
| + | |||
| + | We specify the displacement sign relative to it and analyze the result in the basic size ('''88/170'''): | ||
| + | |||
| + | ''The length of the side section has been subtracted from the length of the center back section. A positive value ('''0.17''')'' ''has been obtained which means that the back section is longer than the side . Therefore, in order to equal these sections, you can extend the side section by displacing its lower point to the right. In this function the point displacement sign is determined by the direction of the axes (“+” – to the right). The analyzed value ('''0.17''')'' ''is positive, so you do not have to change the sign of the values in the tab.'' | ||
| + | |||
| + | |||
| + | * Press the “YES” button to confirm the input of the displacing values. The selected point will be displaced. | ||
| + | |||
| + | * In order to check the displacement performed, select [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image026.jpg]] button of the measurement panel. | ||
| + | |||
| + | A new, recalculated result of the earlier measurement (without a repeated measurement) will be displayed. | ||
| + | |||
| + | * If the displacement direction has been determined incorrectly, you can cancel it (rollback [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image028.jpg]] or [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image030.jpg]] in the program screen menu) and repeat the command having changed the displacement direction. | ||
| + | |||
| + | |||
| + | {| style="border-spacing:0;" | ||
| + | | style="background-color:#ffffff;"| | ||
| + | {| style="border-spacing:0;" | ||
| + | || NOTE | ||
| + | |||
| + | |} | ||
| + | | ||
| + | |||
| + | |} | ||
| + | | ||
| + | |||
| + | |||
| + | When another displacement point is selected, the analysis will be different. | ||
| + | |||
| + | For example, select a point for displacement: ''the lower point of the back section.'' | ||
| + | |||
| + | We specify the displacement sign relative to it and analyze the result in the basic size ('''88/170'''): | ||
| + | |||
| + | ''The length of the side section has been subtracted from the length of the back section. A positive value ('''0.17''')'' ''has been obtained which means that the back section is longer than the side. Therefore, in order to equal these sections, you need to shorten the back section by displacing its lower point to the left.'' | ||
| + | |||
| + | ''In this function the point displacement sign is determined by the direction of the axes (“-” – to the left). The analyzed value ('''0.17''')'' ''is positive, so its sign needs to be changed (''[[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image023.jpg]] ''button).'' ''Negative values in the table will become positive, but if you make a similar analysis for these sizes, it will become clear that it is correct. '' | ||
| + | |||
| + | | ||
| + | |||
| + | '''ATTENTION!''' If the situation arises when the difference has positive and negative value for sizes, the sign is determined based on one of the sizes (any one). | ||
| + | |||
== Checking ratio and correcting section lengths in pairs == | == Checking ratio and correcting section lengths in pairs == | ||
== Setting a required fitting value on a section == | == Setting a required fitting value on a section == | ||
[[Category:Constructor]] | [[Category:Constructor]] | ||
Revision as of 11:26, 18 May 2015
Checking Ratio and Adjusting Lengths of Sections
In order to check the lengths of different sections, the length of one section needs to be measured with the “+” sign and the other – with the “-” sign. Than points of one of the pieces are displaced by the amount of the obtained difference, both lengths are equaled. For example, let us check the ratio of the back princess seam lengths:
- Select File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image002.jpg command of the section measurement (File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image004.jpg sign is selected by default).
- Specify the first section to be measured (1).
- Change the measurement sign by selecting File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image006.jpg button.
- Specify the second section to be measured (2).
File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image008.jpg* Select File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image010.jpg command of the measurement panel to view the difference between the sections for sizes. The difference values are displayed in the “A” tab of the result table.
File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image012.jpg Having analyzed the measurement result, you can adjust the section lengths:
- SelectFile:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image014.jpg command to save the length ratio in the buffer
- Select one of the point displacement functions. For example, File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image015.gif - “Point/ Displace along X”.
· Select the area around the required point and input the displacement value in the function box.
To do this, values need to be read from the buffer (File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image017.jpg) or the size table (File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image019.jpg) should be opened.
The data table in the “F” tab will be opened (the data of the last buffer saved).
- Specify the direction of the point displacement. If necessary, change the value sign File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image023.jpg.
In this example, we select the point for displacement: the lower point of the side section on the princess seam.
We specify the displacement sign relative to it and analyze the result in the basic size (88/170):
The length of the side section has been subtracted from the length of the center back section. A positive value (0.17) has been obtained which means that the back section is longer than the side . Therefore, in order to equal these sections, you can extend the side section by displacing its lower point to the right. In this function the point displacement sign is determined by the direction of the axes (“+” – to the right). The analyzed value (0.17) is positive, so you do not have to change the sign of the values in the tab.
- Press the “YES” button to confirm the input of the displacing values. The selected point will be displaced.
- In order to check the displacement performed, select File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image026.jpg button of the measurement panel.
A new, recalculated result of the earlier measurement (without a repeated measurement) will be displayed.
- If the displacement direction has been determined incorrectly, you can cancel it (rollback File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image028.jpg or File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image030.jpg in the program screen menu) and repeat the command having changed the displacement direction.
|
When another displacement point is selected, the analysis will be different.
For example, select a point for displacement: the lower point of the back section.
We specify the displacement sign relative to it and analyze the result in the basic size (88/170):
The length of the side section has been subtracted from the length of the back section. A positive value (0.17) has been obtained which means that the back section is longer than the side. Therefore, in order to equal these sections, you need to shorten the back section by displacing its lower point to the left.
In this function the point displacement sign is determined by the direction of the axes (“-” – to the left). The analyzed value (0.17) is positive, so its sign needs to be changed (File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image023.jpg button). Negative values in the table will become positive, but if you make a similar analysis for these sizes, it will become clear that it is correct.
ATTENTION! If the situation arises when the difference has positive and negative value for sizes, the sign is determined based on one of the sizes (any one).