Difference between revisions of "Constructor:Contour modifications"

From Julivi Help
Jump to: navigation, search
(→‎Construct an indention)
Line 1: Line 1:
 
== Construct an indention ==
 
== Construct an indention ==
 +
== Contour Modifications ==
 +
      After construction of seams, the external outline of the piece (the Cut) needs to be finished: steps, corners, vents, ledges, etc. These outline modifications are presented as a number of constructions in the SEAMS tab:
 +
 +
 +
      The program enables operating with two types of main outlines: Finished view or Operating outline (i.e. the Cut in its initial state, without piece designing constructions – steps, corners, etc.).
 +
 +
     Options for operating with the main outline in the program:
 +
 +
1) Set a seam from the main outline ('''Ready view''') outward to obtain a derivative outline of the Cut.
 +
 +
2) Set seams from the main outline ('''Operating outline''') inward to form a derivative outline of the Finished view. In this case, another outline based on the main one (the Cut) is automatically created over the Operating outline and copies it during all operations except functions of the SEAMS tab (here, modifications are made on the Cut directly for piece finalizing).
 +
 +
     Thus, the Cut is always a derivative outline, depending on the main outline. The Cut is an outline which is formed when drawing arrangements and is a final, completed state of the piece for cutting with allowances for finishing.
 +
 +
For example, on a piece with the Operating main outline, when constructing a step ( [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image004.jpg]] “Seams/ Create a step”) separation of two outlines: the Cut and the Operating outline (the Cut initial state, without a step) takes place.
 +
 +
 +
<center>&nbsp;</center>
 +
 +
<u>'''ATTENTION! In case of the piece construction changing (removing or adding points and/or sections), modifications on the Cut may be destroyed'''</u> and deleted if there are no more initial elements for construction. This is precisely why modifications of the Cut are called commands of the CUT FINALIZING, they are to be performed at the end of work with the piece.
 +
 +
<u>E.g.:</u> On a section of the piece bottom a hem allowance was constructed using [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image008.jpg]]&nbsp;function (“Cuff”).
 +
 +
3 sections are involved in this construction: the bottom section itself ('''2''') and two adjacent sections ('''1''' and '''3''') which determine the direction of the fold lateral sides.
 +
 +
Then, a point was introduced on the bottom section ('''2'''), and the section was “cut” at this point, i.e. it was divided in two (section '''4''' was added).&nbsp; In this case construction of the fold from section #2 is destroyed because the initial data for the construction have been fundamentally changed.
 +
 +
 +
Modification commands are intended for handling the Cut, but they can also be used for the main outline (Finished view and Operating outline) or Inner and Crosshair outline after deactivating visibility or sensitivity of the Cut ([[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image012.jpg]] button and&nbsp; [[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image014.jpg]]&nbsp;&nbsp;option in the outline visibility screen block).
 +
 +
<u>'''ATTENTION! There is an advantage of operating with the Cut derivative outline: modification reconstruction in case of the main outline changing in accordance with its creation principles. '''</u>
 +
 +
&nbsp;&nbsp;&nbsp;&nbsp; For example, there are seams set outward on a piece with the Finished view main outline, i.e. a Cut derivative outline has been created and the modification – bottom turn up construction ([[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image016.jpg]] function – “Seams/ Cuff”) has been performed <u>on the Cut</u>. This function is based on the principle (RULE) of creating a bottom turn up in such a way that its lateral sections follow the shape of the upper part at the level of the double turn up. &nbsp;When the main outline is changed (deformation, change of length, etc.), the Cut modification will be automatically reconstructed AS PER THE RULES OF ITS CREATION. It means that the bottom turn up &nbsp;on the Cut will <u>automatically</u> follow the shape of the upper part relative to the turn up line with regard to its new changed curving:
 +
 +
 +
&nbsp;
 +
 +
'''ATTENTION!''' In case of modifications of the <u>'''Cut'''</u> outline the capabilities of construction changing are limited by the <u>SEAMS tab commands only</u>, because all program commands are executed on the Main outline, not on the Cut (except the SEAM tab functions).
 +
 +
&nbsp;&nbsp;&nbsp;&nbsp; '''This means that the shape of the Cut can be changed manually, but it is not reasonable (including that on sections of construction of corners, steps, etc.). This is because any change of the Main outline shape causes automatic reconstruction of the Cut in the way it was created initially. '''
 +
 +
&nbsp;
 +
 +
&nbsp;&nbsp;&nbsp;&nbsp; In case of modification of the Cut, a screen logo of this construction is created. Clicking on the logo enables deleting or redesigning the construction with new parameters. &nbsp;&nbsp;
 +
 +
&nbsp;&nbsp;&nbsp;&nbsp; In case of modification of the Main outline, <u>there are no construction logos</u><nowiki>; new sections and points of constructions become parts of the main outline. Consequently, the possibility of automatic redesigning of the whole construction block (a ledge, a cuff, a step) in case of piece shape changing (as on the Cut) is lost.</nowiki>
 +
 +
For example, if the bottom turn up construction command ([[Image:C:%5CDOCUME~1%5Cadmin%5CLOCALS~1%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image016.jpg]] - “Seams/ Cuff”) has been executed right on the main outline, the shape of the turn up &nbsp;has to be adjusted manually in case of hem deformation, or the operation of the bottom turn up creation should be repeated with the new piece shape.
 +
 +
&nbsp;
 +
 +
&nbsp;
 +
 +
&nbsp;
 +
 +
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;FEATURES
 +
 +
A special operational mode has been introduced into the program, where the Cut visibility is not displayed at all. This allows performing all functions of the SEAMS tab directly on the main Operating outline (without special deactivating the Cut visibility on the screen) for pieces with the '''Operating''' '''main outline'''.
 +
 +
For this purpose, the “Display Cut” program setting should be deactivated by turning the option off (“Setting/ Program parameters” text menu items, GENERAL/Constructor tab):
 +
 +
 +
In this operating mode the button of the Cut outline visibility/sensitivity will be blocked.
 +
 +
All program functions work on the Operating main outline, while the Cut follows its shape automatically. <u>And only the SEAMS tab is intended for operating on the Cut</u>. But, having deactivated the Cut visibility (using this setting or manually, on the screen), modifications of the SEAMS tab will also be performed directly on the Operating main outline, while the Cut, invisible on the screen, will appear in arrangements copying the Operating outline precisely.
 +
 
== Construct a corner ==
 
== Construct a corner ==
 
== «Fox ear» ==
 
== «Fox ear» ==

Revision as of 21:21, 15 March 2015

Construct an indention

Contour Modifications

      After construction of seams, the external outline of the piece (the Cut) needs to be finished: steps, corners, vents, ledges, etc. These outline modifications are presented as a number of constructions in the SEAMS tab:


      The program enables operating with two types of main outlines: Finished view or Operating outline (i.e. the Cut in its initial state, without piece designing constructions – steps, corners, etc.).

     Options for operating with the main outline in the program:

1) Set a seam from the main outline (Ready view) outward to obtain a derivative outline of the Cut.

2) Set seams from the main outline (Operating outline) inward to form a derivative outline of the Finished view. In this case, another outline based on the main one (the Cut) is automatically created over the Operating outline and copies it during all operations except functions of the SEAMS tab (here, modifications are made on the Cut directly for piece finalizing).

     Thus, the Cut is always a derivative outline, depending on the main outline. The Cut is an outline which is formed when drawing arrangements and is a final, completed state of the piece for cutting with allowances for finishing.

For example, on a piece with the Operating main outline, when constructing a step ( File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image004.jpg “Seams/ Create a step”) separation of two outlines: the Cut and the Operating outline (the Cut initial state, without a step) takes place.


 

ATTENTION! In case of the piece construction changing (removing or adding points and/or sections), modifications on the Cut may be destroyed and deleted if there are no more initial elements for construction. This is precisely why modifications of the Cut are called commands of the CUT FINALIZING, they are to be performed at the end of work with the piece.

E.g.: On a section of the piece bottom a hem allowance was constructed using File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image008.jpg function (“Cuff”).

3 sections are involved in this construction: the bottom section itself (2) and two adjacent sections (1 and 3) which determine the direction of the fold lateral sides.

Then, a point was introduced on the bottom section (2), and the section was “cut” at this point, i.e. it was divided in two (section 4 was added).  In this case construction of the fold from section #2 is destroyed because the initial data for the construction have been fundamentally changed.


Modification commands are intended for handling the Cut, but they can also be used for the main outline (Finished view and Operating outline) or Inner and Crosshair outline after deactivating visibility or sensitivity of the Cut (File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image012.jpg button and  File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image014.jpg  option in the outline visibility screen block).

ATTENTION! There is an advantage of operating with the Cut derivative outline: modification reconstruction in case of the main outline changing in accordance with its creation principles.

     For example, there are seams set outward on a piece with the Finished view main outline, i.e. a Cut derivative outline has been created and the modification – bottom turn up construction (File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image016.jpg function – “Seams/ Cuff”) has been performed on the Cut. This function is based on the principle (RULE) of creating a bottom turn up in such a way that its lateral sections follow the shape of the upper part at the level of the double turn up.  When the main outline is changed (deformation, change of length, etc.), the Cut modification will be automatically reconstructed AS PER THE RULES OF ITS CREATION. It means that the bottom turn up  on the Cut will automatically follow the shape of the upper part relative to the turn up line with regard to its new changed curving:


 

ATTENTION! In case of modifications of the Cut outline the capabilities of construction changing are limited by the SEAMS tab commands only, because all program commands are executed on the Main outline, not on the Cut (except the SEAM tab functions).

     This means that the shape of the Cut can be changed manually, but it is not reasonable (including that on sections of construction of corners, steps, etc.). This is because any change of the Main outline shape causes automatic reconstruction of the Cut in the way it was created initially.

 

     In case of modification of the Cut, a screen logo of this construction is created. Clicking on the logo enables deleting or redesigning the construction with new parameters.   

     In case of modification of the Main outline, there are no construction logos; new sections and points of constructions become parts of the main outline. Consequently, the possibility of automatic redesigning of the whole construction block (a ledge, a cuff, a step) in case of piece shape changing (as on the Cut) is lost.

For example, if the bottom turn up construction command (File:C:\DOCUME~1\admin\LOCALS~1\Temp\msohtmlclip1\01\clip image016.jpg - “Seams/ Cuff”) has been executed right on the main outline, the shape of the turn up  has to be adjusted manually in case of hem deformation, or the operation of the bottom turn up creation should be repeated with the new piece shape.

 

 

 

                                         FEATURES

A special operational mode has been introduced into the program, where the Cut visibility is not displayed at all. This allows performing all functions of the SEAMS tab directly on the main Operating outline (without special deactivating the Cut visibility on the screen) for pieces with the Operating main outline.

For this purpose, the “Display Cut” program setting should be deactivated by turning the option off (“Setting/ Program parameters” text menu items, GENERAL/Constructor tab):


In this operating mode the button of the Cut outline visibility/sensitivity will be blocked.

All program functions work on the Operating main outline, while the Cut follows its shape automatically. And only the SEAMS tab is intended for operating on the Cut. But, having deactivated the Cut visibility (using this setting or manually, on the screen), modifications of the SEAMS tab will also be performed directly on the Operating main outline, while the Cut, invisible on the screen, will appear in arrangements copying the Operating outline precisely.

Construct a corner

«Fox ear»

Construct a cusp

Figured cutout

Construct a cusp on a corner

Constructing a cuff (fold)

Corner of a sleeve vent

Growing a contour

Cone

Processing a dart

Processing a box pleat

«Bezier» curve

Constructing corners and indents equal by height

Corner by a second piece

Equated indent by a second piece

Equated corner by a second piece

Draw (remove) a gash on a cut

Insert a gash at a cut

Point at a line crossing

Point at a normal to a line

Move a point along XY

Move a point in a direction by...

Aling a cut point vertically (horizontally)

Deleting indents, corners

Aling a dart point

Canceling a performed modification

Reconstructing a performed modification

Examples of modifications

Example №1

Example №2

Example №3