Difference between revisions of "Constructor:Lines"
| Line 40: | Line 40: | ||
# When "Normal"is constructed from the End point, the straight line goes through an angle bisector between the adjacent sections. The construction "Tangent" from an End point has no sense | # When "Normal"is constructed from the End point, the straight line goes through an angle bisector between the adjacent sections. The construction "Tangent" from an End point has no sense | ||
# If there are several crossing places of a straight line and the limiting contour, a line consisting of several sections is created. It is possible to create a different number of sections in different sizes of a graded piece, so it is recommended to check all sizes. | # If there are several crossing places of a straight line and the limiting contour, a line consisting of several sections is created. It is possible to create a different number of sections in different sizes of a graded piece, so it is recommended to check all sizes. | ||
| + | [[File:10.png]] | ||
# You can work with a group of superposed pieces (the [mk:@MSITStore:D:\!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\Лера\help_EN\Maestro.chm::/eiiaiaeu_niaiauaie_eaeae.htm commands] of the screen menu). | # You can work with a group of superposed pieces (the [mk:@MSITStore:D:\!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\Лера\help_EN\Maestro.chm::/eiiaiaeu_niaiauaie_eaeae.htm commands] of the screen menu). | ||
A straight line will be created separately on each piece. | A straight line will be created separately on each piece. | ||
Revision as of 13:20, 5 March 2015
Lines
For making different marks or auxiliary constructions you may often need to draw different types of lines (horizontal, vertical, straight, parallel, etc) on pieces.
These lines are drafted on the piece as inner contours with the help of the commands in the LINES tab or from the text menu "Contour/ Lines":
You can make the following constructions: Horizontal line, Vertical line, Normal and Tangent lines, Equidistant line, Segment of a set length and direction; Straight line between points; Quilting lines.
Straight lines
Straight line from a point
To create a straight line of a set type (horizontal, vertical, normal, tangent) from any point of the section:
You can also follow the text menu points "Contour/ Lines / Straight line from a point".
- Specify the point (1) or any place of the section. The window with the parameters of the straight line is displayed on the screen:
- Limitation for a straight line inside the contour, where a point is specified, is set by default
If necessary, you can select a different type of a limiting contour by means of switching on a necessary type of the switch “Limit”. It can be Cut, Finished view or any locked contour specified upon selection of a point: Inner or Working contour.
- Select the button of a necessary construction command with clicking it with the left mouse button:
-horizontal
-vertical
-normal
-tangent.
ADDITIONAL
MODE Construction of “Normal” and “Tangent” from the End point of a section
To construct “Normal” and “Tangent” from the end point to one of the two adjacent sections of this point, you need to specify, which section will be used. It means that the function must be performed in a special mode:
- Press and hold the <CTRL> key on the keyboard after selection of the function
- Specify not the End point (1) on the screen, but a spot on the section next to it, by means of selection of one of the sections for construction of a normal or a tangent line.
- Release the <CTRL> key at the time of display of the window for input of values or setting the type of a line.
FEATURES
- When constructing lines from the Inner contour, Sight, or Pinhole, contour limitation is performed up to the main contour by default.
- When "Normal"is constructed from the End point, the straight line goes through an angle bisector between the adjacent sections. The construction "Tangent" from an End point has no sense
- If there are several crossing places of a straight line and the limiting contour, a line consisting of several sections is created. It is possible to create a different number of sections in different sizes of a graded piece, so it is recommended to check all sizes.
- You can work with a group of superposed pieces (the [mk:@MSITStore:D:\!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\Лера\help_EN\Maestro.chm::/eiiaiaeu_niaiauaie_eaeae.htm commands] of the screen menu).
A straight line will be created separately on each piece.



