Difference between revisions of "Constructor:Creating cut line"
(Created page with "Modeling operations are mainly performed along a previously drafted modeling line on a piece – Cut line. It can be straight, figured and broken, and can have a type of an In...") |
|||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
Modeling operations are mainly performed along a previously drafted modeling line on a piece – Cut line. It can be straight, figured and broken, and can have a type of an Inner contour or Sight. | Modeling operations are mainly performed along a previously drafted modeling line on a piece – Cut line. It can be straight, figured and broken, and can have a type of an Inner contour or Sight. | ||
| − | Cut line can be drafted arbitrarily on a piece (function [[Image:embim1415.png|embim1415.png]] | + | Cut line can be drafted arbitrarily on a piece (function [[Image:embim1415.png|embim1415.png]] - «Contour/ Create new contour»), or by using the functions of the tab LINES and macrocommands of creating contours. |
| − | + | ||
Arbitrary cut line can be drafted from a point, from any place on a section, or inside a piece plane. Increments from specified places are read automatically: if a point was specified – point increment, if a section was specified – ratio between a spot of a click and length of a section, if a plane inside a piece was specified – zero increments (Contour point is «nailed» to the screen and cannot be graded). | Arbitrary cut line can be drafted from a point, from any place on a section, or inside a piece plane. Increments from specified places are read automatically: if a point was specified – point increment, if a section was specified – ratio between a spot of a click and length of a section, if a plane inside a piece was specified – zero increments (Contour point is «nailed» to the screen and cannot be graded). | ||
| Line 9: | Line 8: | ||
[[Image:embim1417.png|embim1417.png]] It is possible to perform the command without an obvious Cut line, but along a straight line, set by two points, for functions [[Image:embim1418.png|embim1418.png]] - «Cut», «Cut off», «Widen», «Spread conically», «Widen+Spread». | [[Image:embim1417.png|embim1417.png]] It is possible to perform the command without an obvious Cut line, but along a straight line, set by two points, for functions [[Image:embim1418.png|embim1418.png]] - «Cut», «Cut off», «Widen», «Spread conically», «Widen+Spread». | ||
| − | + | To do so, press the <CTRL> key of the keyboard after a function is selected and specify two points (only on the main contour), imitating a cut line, and then proceed using the function as in the mode with a drafted cut line. | |
| − | + | ||
| − | + | [[Image:embim1419.png|embim1419.png]] Contours, FULLY located outside the main contour of a piece, disappear after performing modeling functions! I necessary, a piece copy must be made prior to modeling, and copy contours back after modeling. | |
| + | [[Category:Constructor]] | ||
Latest revision as of 14:31, 5 March 2015
Modeling operations are mainly performed along a previously drafted modeling line on a piece – Cut line. It can be straight, figured and broken, and can have a type of an Inner contour or Sight.
Cut line can be drafted arbitrarily on a piece (function
- «Contour/ Create new contour»), or by using the functions of the tab LINES and macrocommands of creating contours.
Arbitrary cut line can be drafted from a point, from any place on a section, or inside a piece plane. Increments from specified places are read automatically: if a point was specified – point increment, if a section was specified – ratio between a spot of a click and length of a section, if a plane inside a piece was specified – zero increments (Contour point is «nailed» to the screen and cannot be graded).
ATTENTION! After a figured line is drafted, the function
- «Section/ Grade section again» must be performed, to create a curve in various sizes to match the basic size (that is why it is important to draft an arbitrary line precisely in the basic size).
It is possible to perform the command without an obvious Cut line, but along a straight line, set by two points, for functions
- «Cut», «Cut off», «Widen», «Spread conically», «Widen+Spread».
To do so, press the <CTRL> key of the keyboard after a function is selected and specify two points (only on the main contour), imitating a cut line, and then proceed using the function as in the mode with a drafted cut line.
Contours, FULLY located outside the main contour of a piece, disappear after performing modeling functions! I necessary, a piece copy must be made prior to modeling, and copy contours back after modeling.