Difference between revisions of "Constructor:Modeling functions"
(Created page with "== Cut a piece into two parts == == Cut off a piece == == Widen a piece == == Conic spread == == Widen and spread a piece (folds) == == Moving a dart == == Close a dar...") |
|||
| (32 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
== Cut a piece into two parts == | == Cut a piece into two parts == | ||
| + | |||
| + | To cut a piece into two parts: | ||
| + | *Select the MODELING tab and the button [[Image:embim1420.png|embim1420.png]] in this tab. The cursor view is changed to [[Image:embim1421.png|embim1421.png]] You can also follow the text menu points “Piece/ Model/ Cut a piece”. | ||
| + | *Specify the cut line of the piece'''(1)''' | ||
| + | *Specify one of the piece sections '''(2)'''. The window with cutting parameters is displayed on the screen: | ||
| + | |||
| + | [[Image:embim1422.png|embim1422.png]] [[Image:embim1423.png|embim1423.png]] | ||
| + | |||
| + | *If necessary, set seam allowances for the section to be cut: “Seam allowance 1” for the section ('''2''') selected while performing the function. “Seam allowance 2” for the second section. | ||
| + | *Press the YES button to confirm input of the data, press the CANCEL button to cancel it. | ||
| + | |||
| + | The working piece will remain unchanged, and 2 new untitled pieces will be created on the screen. If the reference piece was rotated with one of the functions for screen rotation, new pieces will be displayed on the screen according to placement of the working piece in the database. | ||
| + | |||
| + | [[Image:embim1417.png|embim1417.png]] It is possible to perform the command without an evident Cut line, but along a straight line set with two points. | ||
| + | To do so, press the <CTRL> key on the keyboard after selection of the function and specify two points on the main contour, imitating a cut line. Then proceed the function as in the mode with a drafted cut line (specify one of the piece parts (2)). | ||
| + | |||
| + | [[Image:embim1425.png|embim1425.png]] | ||
| + | |||
| + | |||
| + | [[Image:embim1419.png|embim1419.png]] 1) With the help of the functions of the SEAMS tab [[Image:embim1427.png|embim1427.png]] “Indention”, “Corner”, “Fox ear” you can design cut sections on the pieces with seam allowances. | ||
| + | |||
| + | [[Image:embim1428.png|embim1428.png]] | ||
| + | |||
| + | 2) For superposed pieces, the function works on the extension of the cut line, if this line does not reach the piece border. For free pieces, the function works exactly along the cut line | ||
| + | |||
| + | [[Image:embim1429.png|embim1429.png]] | ||
| + | |||
== Cut off a piece == | == Cut off a piece == | ||
| + | |||
| + | To cut off a part of a piece: | ||
| + | |||
| + | *Select the tab MODELING and the button [[Image:embim1430.png|embim1420.png]]in the tab. The cursor view changes to [[Image:embim1421.png|embim1421.png]]. It is also possible to follow text menu points «Piece/ Model/ Cut a piece». | ||
| + | *Specify a line for cutting a piece '''(1)''' | ||
| + | *Specify the remaining part of a piece '''(2)'''. One specified part of a piece remains on the screen. | ||
| + | |||
| + | [[Image:embim1432.png|embim1432.png]] | ||
| + | |||
| + | Additional mode is same as described for the function | ||
| + | [[Image:embim1420.png|embim1420.png]] «Cut a piece» | ||
| + | |||
| + | [[Image:Embim1419.png|Embim1419.png]] When selecting the remaining part of a piece, it is best not to select a section, from which the cut line runs, but choose a section adjacent to it instead. If a cut line does not run from a final point, it is possible that separate parts of a piece in the graded nest will be clicked . | ||
| + | |||
| + | [[Image:embim1435.png|embim1435.png]] | ||
| + | |||
| + | '''ATTENTION!''' This method of selecting the working section (remaining, rotated, moved) works for other modeling functions as well. | ||
| + | Other specifics are the same as described for the function [[Image:embim1420.png|embim1420.png]] «Cut a piece into 2 parts» | ||
| + | |||
== Widen a piece == | == Widen a piece == | ||
| + | |||
| + | To widen a piece (for example, to form folds and tucks): | ||
| + | *Select the tab MODELING and the button [[Image:embim1437.png|embim1437.png]] in this tab. The cursor view changes to [[Image:embim1438.png|embim1438.png]] . | ||
| + | It is also possible to follow text menu points «Piece/Model/ Widen piece». | ||
| + | *Specify cut line ('''1''') | ||
| + | *Specify a part of a piece to be moved ('''2'''). The window with widening parameters is displayed on the screen: | ||
| + | |||
| + | [[Image:embim1439.png|embim1439.png]] | ||
| + | |||
| + | Set widening value in the window «Widen by» and select a type of widening: [[Image:embim1440.png|embim1440.png]] - widening will take place at normal to chord (in other words – to the straight line, which connects final points of the cut line). | ||
| + | |||
| + | [[Image:embim1441.png|embim1441.png]] | ||
| + | |||
| + | [[Image:embim1442.png|embim1442.png]] - Widening in the coordinate system ХУ, on rotated axis [[Image:embim1443.png|embim1443.png]] as well. Additional windows for entering X and Y values are displayed in the window with widening parameters: | ||
| + | |||
| + | [[Image:embim1444.png|embim1444.png]] | ||
| + | |||
| + | [[Image:embim1445.png|embim1445.png]] | ||
| + | |||
| + | When widening in the mode «At normal to chord», a specified side ('''2''') determines positive direction for moving the selected part of a piece. ('''2а''' – moving a part to the right, '''2б''' – to the left) | ||
| + | |||
| + | [[Image:embim1446.png|embim1446.png]] | ||
| + | |||
| + | *Press the YES button to confirm data input, press CANCEL to cancel. | ||
| + | Additional mode (working without a cut line) is the same as described for the function [[Image:Embim1420.png|Embim1420.png]] «Cut a piece» | ||
| + | |||
| + | [[Image:embim1419.png|embim1419.png]] | ||
| + | |||
| + | 1) When working with superposed pieces, upon specifying a side to be widened, a piece that was fixed upon superposition must be selected. | ||
| + | |||
| + | 2) Functions of the tab SEAMS [[Image:embim1449.png|embim1449.png]] «Designing a dart» (for Cut contour) and [[Image:embim1450.png|embim1450.png]] «Set dart point» (for the main contour) can be used to design ends of the widened section. | ||
| + | |||
| + | [[Image:embim1451.png|embim1451.png]] | ||
| + | |||
| + | Other specifics are the same as described for the function [[Image:Embim1430.png|Embim1430.png]] «Cut a piece» | ||
| + | |||
== Conic spread == | == Conic spread == | ||
| + | |||
| + | |||
| + | |||
| + | The function allows to rotate selected sections of a piece by a set value. To do so: | ||
| + | *Select the tab MODELING and the button [[Image:embim1453.png|embim1453.png]] in this tab. The cursor view changes to [[Image:embim1454.png|embim1454.png]]. | ||
| + | It is also possible to follow text menu points «Piece/Model/ Conic spread». | ||
| + | *Specify a point which is rotation center ('''1''') (a point on the cut line), | ||
| + | *Specify a point ('''2''') for setting opening | ||
| + | *Specify a part of a piece to be rotated ('''3'''). The window of function parameters is displayed on the screen: | ||
| + | |||
| + | [[Image:embim1455.png|embim1455.png]][[Image:embim1456.png|embim1456.png]] | ||
| + | |||
| + | *Set the spread value in the cell «Spread». When a positive value is entered, spread action is performed, when a negative value is entered - closing (piece sections «cover» each other). | ||
| + | |||
| + | To enter spread values differing by size, press the button [[Image:embim1457.png|embim1457.png]].The window is displayed on the screen: | ||
| + | [[Image:embim1458.png|embim1458.png]] | ||
| + | |||
| + | It is possible to enter values differing by size manually (button [[Image:embim1459.png|embim1459.png]] ), or from the buffer (button [[Image:Embim2450.png|Embim2450.png]] ). | ||
| + | |||
| + | [[Image:embim1461.png|embim1461.png]] | ||
| + | To confirm spread value press the YES button, to cancel - the CANCEL button. | ||
| + | |||
| + | Other functions of data input: [[Image:Embim2450.png|Embim2450.png]] [[Image:Embim2448.png|Embim2448.png]] - read from buffer or input to buffer calculation of «Seam algebra» [[Image:Embim2439.png|Embim2439.png]] [[Image:Embim2441.png|Embim2441.png]] - save to file or read from file [[Image:Embim2437.png|Embim2437.png]] - clear the table | ||
| + | *Determine a section of a piece to be rotated: [[Image:embim1467.png|embim1467.png]] - rotation only of one, specified section of a piece | ||
| + | *[[Image:embim1468.png|embim1468.png]] - rotation of both sections of a piece to different sides symmetrical to the cut line. | ||
| + | *Select type of cut design upon tearing «Cut», «Dart», «Tuck»: | ||
| + | [[Image:embim1469.png|embim1469.png]] | ||
| + | |||
| + | It is possible to set value of sections at the end of a tuck in the mode [[Image:embim1470.png|embim1470.png]] | ||
| + | |||
| + | *Press the YES button to confirm spread parameters, press CANCEL to cancel. | ||
| + | Additional mode (without cut line) is the same as described for the function [[Image:Embim1420.png|Embim1420.png]] «Cut a piece into 2 parts» | ||
| + | |||
| + | [[Image:Embim1419.png|Embim1419.png]] 1) When the function is performed for a broken line, it is possible to specify any point of the broken line as a point for creating spread. | ||
| + | For example: creating a dart under a lapel by using a part of a bust dart opening: | ||
| + | |||
| + | [[Image:embim1473.png|embim1473.png]] | ||
| + | |||
| + | 2) For superposed pieces, the function does not work along the cut line, but only at points (additional mode with holding the <CTRL> key prior to using the function). A message is displayed: | ||
| + | |||
| + | [[Image:embim1474.png|embim1474.png]] | ||
| + | |||
| + | 3) An option for designing cuts «Cut out» is not applicable to superposed pieces (as inessential). | ||
| + | 4) To perform the function with superposed pieces, pieces should be superposed without a gap between them along the spread line. Otherwise values of INTERMEDIATE spread on these pieces will differ: spread will be calculated for the second piece on account of the gap between pieces. | ||
| + | [[Image:embim1475.png|embim1475.png]] | ||
| + | |||
| + | 5) The functions of the tab SEAMS [[Image:embim1449.png|embim1449.png]] «Dart design» (for Cut contour) and [[Image:Embim1450.png|embim1450.png]] «Set dart point» (for the main contour) can be used to design the end of the spread. | ||
| + | |||
== Widen and spread a piece (folds) == | == Widen and spread a piece (folds) == | ||
| + | |||
| + | To widen a part of a piece with further spread (creating gathers, folds, etc.): | ||
| + | *Select the tab MODELING and the button [[Image:embim1478.png|embim1478.png]] in this tab. The cursor view changes to [[Image:embim1479.png|embim1479.png]] | ||
| + | It is possible to follow text menu points «Piece/Model/Widen + spread a piece». | ||
| + | |||
| + | *Specify the end of a cut line near the first point (1) | ||
| + | *Specify the end of a line near the second point (2) | ||
| + | *Specify a section of a piece to be rotated (3). The window with parameters for widening is displayed on the screen: | ||
| + | |||
| + | [[Image:embim1480.png|embim1480.png]][[Image:embim1481.png|embim1480.png]] | ||
| + | |||
| + | *Set opening in the first and second point accordingly by using cells «Opening №1» and «Opening №2». When a positive value is entered, a piece is spread, when a negative value is entered - it is closed (piece section «cover» each other). It is possible to set opening in one point and joining in another. | ||
| + | |||
| + | To enter spread values differing by size, press the button [[Image:embim1482.png|embim1482.png]]. Standard input window is displayed on the scree, where it is possible to enter values manually (button [[Image:embim1483.png|embim1483.png]]), or from the buffer (button [[Image:embim1484.png|embim1484.png]]). | ||
| + | |||
| + | *Specify a section of a piece to be rotated by switching on a require option in the setting «Rotate»: | ||
| + | |||
| + | [[Image:embim1485.png|embim1485.png]] - rotation of only one, specified part of a piece | ||
| + | |||
| + | [[Image:embim1486.png|embim1486.png]] - rotation of both parts of a piece to different sides, symmetrically with reference to the cut line. | ||
| + | *To confirm spread parameters press the YES button, to cancel - press CANCEL. | ||
| + | To create several folds, draft several cut lines on a piece and perform the function for each line one by one. | ||
| + | |||
| + | The functions of the tab SEAMS [[Image:embim1487.png|embim1487.png]] «Dart design» (for Cut contour) and [[Image:embim1488.png|embim1488.png]] «Set dart point» (for the main contour) can be used to design the end of the spread. | ||
| + | |||
| + | The mode [[Image:embim1489.png|embim1489.png]] is used to perform double spread (box pleat). To construct it, switch on the mode «Box pleats» in the parameters window, and enter total value of spread in cells «Opening №1» and «Opening №2». The spread function will be performed twice, to both sides of pressing the fold towards the center. | ||
| + | |||
| + | [[Image:embim1490.png|embim1490.png]] | ||
| + | |||
| + | It is possible to enter zero spread, but only for all sizes of a graded nest, otherwise the graded nest will be incorrect (there are fold sections in some sizes, but not in others) | ||
| + | The function of the tab SEAMS [[Image:embim1491.png|embim1491.png]] - «Designing box pleat» is used to design the pleat, setting points with reference to the press direction: | ||
| + | |||
| + | [[Image:embim1492.png|embim1492.png]] | ||
| + | |||
== Moving a dart == | == Moving a dart == | ||
| + | |||
| + | To move a dart: | ||
| + | *Select the tab MODELING and the button [[Image:embim1493.png|embim1493.png]] in this tab. The cursor view changes to [[Image:embim1494.png|embim1494.png]]. | ||
| + | It is also possible to follow text menu points «Piece/ Model/ Move a dart». | ||
| + | *Specify a fixed side of a dart ('''1''') on the main contour | ||
| + | *Specify a side of a dart to be moved ('''2''') on the main contour | ||
| + | *Specify the center of a dart ('''3''') on the main contour | ||
| + | *Specify a cut line ('''4'''). The window of parameters for moving the dart is displayed on the screen: | ||
| + | |||
| + | [[Image:embim1495.png|embim1495.png]][[Image:embim1496.png|embim1496.png]] | ||
| + | |||
| + | *Select the value of dart movement, by switching on a required option of the parameter «Close»: | ||
| + | [[Image:embim1479.png|embim1497.png]] - part from the general opening of a dart (1.0 – entire opening, 0.5 – half of the opening, etc.) | ||
| + | [[Image:embim1479.png|embim1498.png]] - value in working measurement units (centimeters, millimeters, inches) | ||
| + | *Select type of a cut design in place of the shift. To do so, select an option of the parameter «Tear» - lock, cutting out or tuck (with setting length of segments at the end of the tuck) | ||
| + | |||
| + | [[Image:embim1499.png|embim1499.png]] | ||
| + | |||
| + | When a dart is moved partially, select design type and place of a tear, and the remaining part. | ||
| + | |||
| + | [[Image:embim1500.png|embim1500.png]] | ||
| + | |||
| + | *Select an option for compensating difference of sides by selecting an option of the setting «Deform». | ||
| + | If dart sides are different in length, sections of closing the darts can be designed by deforming : [[Image:embim1501.png|embim1501.png]]- one of the dart sides will become shorter, the other one - longer, averaging out both lengths. [[Image:embim1502.png|embim1482.png]] - only flexible part of a piece will be corrected in length. [[Image:embim1503.png|embim1483.png]] - only fixed part of a piece will be corrected in length. [[Image:embim1504.png|embim1484.png]]- side lengths do not change, additional section will be constructed in the place of closure. | ||
| + | *To confirm shift parameters press the YES button, to cancel - press CANCEL. | ||
| + | |||
| + | [[Image:embim1505.png|embim1485.png]] To transfer a dart to several places at once: | ||
| + | *After the function has been selected, specify a fixed side ('''1'''), side to be moved ('''2''') and a point - center of the dart ('''3''') on the main contour. | ||
| + | *Specify one or several points - areas for transferring the dart - while holding down the <SHIFT> key of the keyboard. | ||
| + | To move a dart to several points specify points ('''4,5,6''') on the main contour one by one. | ||
| + | The dart is moved to several places directly without constructing a cut line. | ||
| + | |||
| + | To move a dart to several lines, final points ('''4,5,6''') o cut lines (figured, broken) need to be specified one by one, it is mandatoryto switch off sensitivity of the main contour | ||
| + | |||
| + | [[Image:embim1506.png|embim1479.png]] | ||
| + | |||
| + | [[Image:embim1507.png|embim1479.png]] | ||
| + | |||
| + | 1) Dart movement is not applicable to superposed pieces. | ||
| + | 2) Dart sides are specified only on the main contour (Working cut or Finished view). | ||
| + | |||
| + | [[Image:embim1508.png|embim1479.png]] | ||
| + | |||
| + | 3) When several movement places are selected, the command [[Image:embim1509.png|embim1479.png]] «Cancel last selection» works only without letting go of the <SHIFT> key. | ||
| + | 4) When the function is performed, contours «Grain line» and «Title», «Text» are not moved. | ||
| + | |||
== Close a dart == | == Close a dart == | ||
| + | |||
| + | The function is often used to move a dart to a seam when a piece is being cut. So, by cutting off a yoke on a skirt, it is possible to close the dart on it and it will be automatically transferred to the seam, to which a yoke is stitched. | ||
| + | |||
| + | [[File:embim1510.png]] | ||
| + | |||
| + | To close a dart: | ||
| + | *Select the tab MODELING and the button [[File:embim1511.png]] in this tab. The cursor view changes to [[File:embim1512.png]]. | ||
| + | It is also possible to follow text menu points «Piece/ Model/ Close a dart». | ||
| + | *Specify a fixed side of a dart ('''1''') on the main contour | ||
| + | *Specify a side of a dart which will be rotated ('''2''') on the main contour | ||
| + | *Specify a point - dart center ('''3''') on the main contour. The window of function parameters is displayed: | ||
| + | |||
| + | [[File:embim1513.png]][[File:embim1514.png]] | ||
| + | |||
| + | *Enter a portion of closing the total opening of a dart in the cell [[:File:embim1515.png]] (1.0 – entire opening, 0.5 – half, etc.) | ||
| + | *Select an option for rotating piece parts by switching on an option «Rotate»: | ||
| + | |||
| + | [[File:embim1516.png]] - both parts symmetrically | ||
| + | |||
| + | [[File:embim1517.png]] - only a specified side ('''2'''). | ||
| + | |||
| + | *Select a version of an option «Deform» for different length of dart sides: [[File:embim1518.png]] - one of the dart sides will become shorter, the other will be extended, averaging out both lengths .[[File:embim1519.png]] - only a fixed part of a piece will be corrected in length.[[File:embim1520.png]] - only a movable part of a piece will be corrected in length.[[File:embim1521.png]] - Length of dart sides is unchanged, a section is constructed in the place of closure. | ||
| + | Compensation of dart sides is not performed upon a partial dart closure. | ||
| + | *Press the YES button to confirm parameters, press CANCEL to cancel. | ||
| + | |||
| + | [[File:embim1522.png]] 1) Dart movement is not applicable to superposed pieces. | ||
| + | 2) Dart sides are specified only on the main contour (Working cut or Finished view). | ||
| + | |||
| + | [[File:embim1523.png]] | ||
| + | |||
| + | 3) When the function is performed, contours «Grain line» and «Title», «Text» are not moved. | ||
| + | 4) If the dart center is not an extreme point of a piece (entire piece of a skirt, not a cut off yoke), the opening of a dart being closed is moved to a line, which is extension of the line in the middle of a dart: | ||
| + | |||
| + | [[File:embim1524.png]] | ||
| + | |||
== Assemble a piece == | == Assemble a piece == | ||
| + | The function is used to create a new piece by assembling it from suitable construction elements of one or several superposed pieces. | ||
| + | It is possible to superpose several pieces, placing them over each other, draft required inner contour, construct seams – in other words, prepare all composing lines of a new piece. For example, to construct forepart lining, place a piece of under-lapel section on the forepart, draft required seam width along the stitching line of the under-lapel section, and perform piece assembly function according to the created reference lines. It is possible to construct a seamless sleeve via the graphic method, by superposing pieces of a sleeve and a bodice in a required manner, etc. | ||
| + | |||
| + | To assemble a piece: | ||
| + | |||
| + | *Select the tab MODELING and the button [[File:embim1525.png]] in this tab. The cursor view changes to [[File:embim1526.png]]. | ||
| + | It is also possible to follow text menu points «Piece/ Model/ Assemble a piece» | ||
| + | *The assembly parameters window is displayed on the screen, a type of a assembled contour must be selected in this window (this will be the main contour of a future piece): Finished view or Cut. | ||
| + | |||
| + | '''ATTENTION!''' When a Cut type is selected, two contours are automatically created: the main contour – Working, and a contour that copies it (derived) – Cut, which will be drafted in the layouts. | ||
| + | |||
| + | [[File:embim1527.png]][[File:embim1528.png]] | ||
| + | |||
| + | *Specify parts of a new piece '''clockwise''' one by one. It is possible to specify sections of any contours: finished view ('''1,2,5,6'''), cut, inner contours ('''3,4'''), grain line. | ||
| + | It is '''recommended''' to begin assembly from a section with defined borders or from a locked section. | ||
| + | *Select the type of connecting sections. | ||
| + | |||
| + | *Select the type of connecting sections. | ||
| + | Sections may not have exact superposition (not reach the next section or cross it with extension), so one of the types of the setting «Combination» must be selected: [[File:embim1529.png]] - crossing of the specified sections will be found upon assembling a piece. This is the connection type that is used most often. | ||
| + | '''ATTENTION! Parts, which continue beyond the border of crossing the following assembled section (beyond the place of connection), MUST be specified on that section of a piece, which will be included in the future piece.''' | ||
| + | |||
| + | For example, when assembling an under-lapel piece from lines of the inner contour and forepart sections, the shoulder section must be specified as close as possible to the neck (if the shoulder section is whole) | ||
| + | |||
| + | [[File:embim1530.png]] | ||
| + | |||
| + | [[File:embim1531.png]] - specified sections are connected with a straight line. | ||
| + | After this mode is selected, assembled section must be specified near its beginning. | ||
| + | |||
| + | [[File:embim1532.png]] | ||
| + | |||
| + | [[File:embim1533.png]] - specified sections will be connected at an average line between them (for example, if sections do not match exactly and pieces are almost parallel). | ||
| + | After this mode is selected, assembled section must be specified near its beginning. | ||
| + | |||
| + | [[File:embim1534.png]] | ||
| + | |||
| + | '''Order of selecting connection''': Select a section, then select the mode of connecting this section to the next section (Crossing, Averaging, Section insertion). Select a section again (the following section, for connecting with which the mode was selected), then, if a mode changes, select the mode again, etc. | ||
| + | |||
| + | *It is possible to change the grain line direction of a new piece by selecting a required option in the setting «Grain line» [[File:embim1535.png]] - similar to the grain line placement of the first specified section.[[File:embim1536.png]] - horizontally with reference to the screen.[[File:embim1537.png]] - vertically with reference to the screen. | ||
| + | *If necessary, inner contours can be input in the new piece (to draft a supporting line, a mark on a new piece at once). To do so: select the button [[File:embim1538.png]] (or another contour type) after assembling the main contour, and specify sections of an inner contour. The button [[File:embim1539.png]] is used to assemble another contour (for example, contour of a dart and a pocket). | ||
| + | *Click the right mouse button. A new (untitled) piece is displayed on the screen. | ||
| + | The function parameters window remains on the screen and it is possible to assemble a new piece. | ||
| + | *Press the CANCEL button to finish using the function. | ||
| + | |||
| + | [[File:embim1540.png]] | ||
| + | |||
| + | 1)'''Cancel the last selected element''' | ||
| + | If a section (or several sections) is selected in error while using the function, it is possible to cancel the last section selection. Without quitting the function «Assemble a piece» (without clicking the right mouse button), click the button [[File:embim1541.png]] of the screen button menu as many times as the number of elements to be canceled. After this, proceed with assembling a piece. | ||
| + | |||
| + | 2)'''Stop command performance''' | ||
| + | The button [[File:embim1542.png]] of the screen button menu is activated while working with the function «Assemble a piece», this button allows to quit command performance without creating incorrect pieces on the screen | ||
| + | |||
| + | 3) Clicking a section in a given size determines the place of a click proportionally for an entire graded nest. It is possible that in different sizes a place of a click will be on different sides from the following crossing section (if increment value in a point has a wide range). | ||
| + | |||
| + | [[File:embim1543.png]] | ||
| + | |||
| + | In this case it is recommended to specify a section in a different area, with a clear location in the entire graded nest. | ||
| + | |||
| + | 4) If incorrect crossing of sections results from the assembly process, error message is displayed but a piece is displayed on the screen. In this case, a piece will be automatically locked with segments, but it is necessary to check possibility of crossing for specified sections in graded nest sizes. | ||
| + | |||
| + | [[File:embim1544.png]] | ||
| + | |||
| + | 5) When specifying assembled sections, it is possible to switch off sensitivity and contour visibility (panel of contour visibility in the screen button menu) at the same time. | ||
| + | |||
| + | 6) When 2 points of line crossing are present, there is a problem of selecting one of them, which can result in an incorrect assembly. | ||
| + | For example, having superposed a forepart and a side section of a jacket in 2 points, it will not be possible to assemble a whole detail, if relief seams consist of one section. Two crossing points are created - on the shoulder and on the bust, the program will arbitrarily select one of these points –for example, on the shoulder. As a result, we have a piece with «intertwining» on the relief seam – a view fully similar to the two superposed pieces. In this case, relief section should have been divided into several parts before assembly («cut» bust points, making them Final). | ||
| + | |||
| + | [[File:embim1545.png]] | ||
| + | |||
| + | 7) It is possible to set a required main contour in the program settings (text menu points «Settings/ Program parameters», tab GENERAL/ Constructor) while performing the function, which will always be displayed by default when the command button is selected. | ||
| + | |||
| + | [[File:embim1546.png]] | ||
| + | |||
| + | 8) If it is necessary to assemble a piece with a different number of sections (for example – a forepart, where a dart is constructed in some sizes), assembly must be started with the first (clockwise) common section after the dart. In other words, dart sections, which are not present in some sizes, have to be last in the assembly process and have large numbers, common for them. | ||
| + | |||
== Join two pieces == | == Join two pieces == | ||
| + | |||
| + | To join two pieces together: | ||
| + | *Select the tab MODELING and the button [[File:embim1547.png]] in the tab. The cursor view changes to [[File:embim1548.png]]. | ||
| + | It is also possible to follow text menu points «Piece/Model/Join two pieces». | ||
| + | *Specify the beginning of a section being copied ('''1''') and the beginning of a section being replaced ('''2''') | ||
| + | *Specify the end of section being copied ('''3''') and the end of a section being replaced ('''4'''). | ||
| + | |||
| + | [[File:embim1549.png]] | ||
| + | |||
| + | *A window is displayed on the screen, where YES button must be pressed to confirm function performance | ||
| + | |||
| + | [[File:embim1550.png]] | ||
| + | |||
| + | If an option «Deform ends» is switched on, difference in section lengths will be made equal. | ||
| + | When this mode is switched off, difference in length is compensated by a locking section. | ||
| + | |||
| + | As a result of the function performance, only a piece, specified for section replacement, is changed: its «replaced» sections disappear, instead of them, «copied» sections are inserted in the contour (clockwise) as if «gluing» 2 pieces. A piece, which sections were copied, remains unchanged. | ||
| + | This function is almost completely the same as the function [[File:embim1551.png]] «Section/ Replace section». | ||
| + | |||
== Spread a piece == | == Spread a piece == | ||
| + | |||
| + | To spread a piece conically by a set number of folds with a required opening: | ||
| + | *Select the tab MODELING and the button [[File:embim1552.png]] in the tab. The cursor view changes to [[File:embim1553.png]]. It is also possible to follow text menu points «Piece/ Model/ Spread a piece» | ||
| + | *Specify a section ('''1''') – place of location for rotation centers of a piece. | ||
| + | It is possible to specify several sections by holding down the <SHIFT> key of the keyboard. | ||
| + | It is possible to specify a portion of a section by specifying its 2 points while pressing the <CTRL> key (and releasing at once). | ||
| + | *Specify a rotated section of a piece ('''2'''). The window of data input is displayed on the screen: | ||
| + | |||
| + | [[File:embim1554.png]] | ||
| + | |||
| + | *Enter total spread value in the cell «Opening». | ||
| + | |||
| + | To enter different values by size use the button of size-by-size input [[File:embim1555.png]]. Standard data input window is displayed on the screen: | ||
| + | [[File:embim1556.png]] | ||
| + | |||
| + | It is possible to enter values different by size manually (button [[File:embim1557.png]]), or from the buffer (button [[File:embim1558.png]]). | ||
| + | *Set required spread parameters: | ||
| + | |||
| + | [[File:embim1559.png]] - two sides of a fold will be drafted on a piece - the line of actual spread | ||
| + | |||
| + | When a number of lines is set automatically, step between them equals 1cm. | ||
| + | If automatic setting is switched off, the cell «Number of lines» will be unblocked, and it will be possible to enter a required number of spread lines by hand. | ||
| + | |||
| + | [[File:embim1560.png]] | ||
| + | |||
| + | *Press the YES button to confirm spread parameters, press CANCEL to cancel. | ||
| + | The reference section ('''1''') (or several section, or a portion of a section) will be divided equally according to the set number of lines - normals, and conic spread will be performed with equal division of a total opening value by a number of folds. | ||
| + | |||
| + | [[File:embim1561.png]] | ||
| + | |||
| + | [[File:embim1562.png]] | ||
| + | |||
| + | 1)Existing points are saved on the section, which will be spread, but new points are not inserted at the level of spread lines. | ||
| + | Points can be input manually by using the function [[File:embim1563.png]] - «Point/ Input point at crossing». | ||
| + | 2)The function is not applicable to superposed pieces. | ||
| + | |||
== Spread a piece by lines == | == Spread a piece by lines == | ||
| + | |||
| + | |||
| + | The function allows to perform conic spread of a piece by several cut lines at once. | ||
| + | Cut lines can be drafted arbitrarily on a piece (the function [[File:embim1564.png]] - «Contour/ Create new contour»), or using the function of the LINES tab and macrocommands for creating contours. Lines can be straight or figured (but not broken) | ||
| + | To perform conic spread of a piece by lines: | ||
| + | *Select the tab MODELING and the button [[File:embim1565.png]] in it. the cursor view changes to [[File:embim1566.png]]. | ||
| + | It is also possible to follow text menu points «Piece/ Model/ Spread a piece by lines» | ||
| + | *Specify a line of a spread (inner contour or sight contour) near the center of piece rotation. | ||
| + | It is possible to specify several lines for spreading ('''1,2,3,4,5,6,7''') one by one while holding down the <SHIFT> key of the keyboard. The data input window is displayed on the screen: | ||
| + | |||
| + | [[File:embim1567.png]] | ||
| + | |||
| + | *Enter total spread value in the cell «Opening». | ||
| + | To enter different values by sizes use the size-by-size input button [[File:embim1568.png]]. Standard data input window is displayed on the screen: | ||
| + | |||
| + | [[File:embim1569.png]] | ||
| + | |||
| + | It is possible to input values different by size manually (button [[File:embim1570.png]]), or from the buffer (button [[File:embim1571.png]]). | ||
| + | *Set required spread parameters: | ||
| + | [[File:embim1572.png]] - two sides of a fold will be drafted on a piece - a line of actual spread | ||
| + | |||
| + | [[File:embim1573.png]] | ||
| + | |||
| + | [[File:embim1574.png]] - symmetrical spread to both sides from each spread line. | ||
| + | When a parameter is switched off, spread direction is determined by the first of specified lines. | ||
| + | [[File:embim1575.png]] - allows to smooth out a section automatically after spreading. It is possible that ends of spread lines will not match the smoothed curve: | ||
| + | |||
| + | [[File:embim1576.png]] | ||
| + | |||
| + | *Press the YES button to confirm spread parameters, press CANCEL to cancel. | ||
| + | Conic spread will be performed along all specified lines with equal division of the total opening value by a number of lines | ||
| + | |||
| + | [[File:embim1577.png]] | ||
| + | |||
| + | If only one spread line is used: | ||
| + | *Specify spread line ('''1''') (inner contour or sight contour) near the center of piece rotation. | ||
| + | *Specify a section of a piece to be rotated ('''2'''). | ||
| + | |||
| + | [[File:embim1578.png]] | ||
| + | |||
| + | It is still possible to use the switch «To both sides», when both parts of a piece will be rotated on the screen with reference to the cut line. | ||
| + | This mode differs from the function «Conic spread» [[File:embim1579.png]] because a number of sections on a piece will not change, and due to this, zero value input is applicable for some sizes when working with the buffer of «Seam algebra». For example, it is possible to correct cap length when working with models on the basis of previously used models. | ||
| + | Specifics are similar to those described for the function [[File:embim1580.png]] - «Piece/ Model/ Spread a piece» | ||
| + | [[Category:Constructor]] | ||
Latest revision as of 13:03, 6 March 2015
Contents
Cut a piece into two parts
To cut a piece into two parts:
- Select the MODELING tab and the button
in this tab. The cursor view is changed to
You can also follow the text menu points “Piece/ Model/ Cut a piece”. - Specify the cut line of the piece(1)
- Specify one of the piece sections (2). The window with cutting parameters is displayed on the screen:
- If necessary, set seam allowances for the section to be cut: “Seam allowance 1” for the section (2) selected while performing the function. “Seam allowance 2” for the second section.
- Press the YES button to confirm input of the data, press the CANCEL button to cancel it.
The working piece will remain unchanged, and 2 new untitled pieces will be created on the screen. If the reference piece was rotated with one of the functions for screen rotation, new pieces will be displayed on the screen according to placement of the working piece in the database.
It is possible to perform the command without an evident Cut line, but along a straight line set with two points.
To do so, press the <CTRL> key on the keyboard after selection of the function and specify two points on the main contour, imitating a cut line. Then proceed the function as in the mode with a drafted cut line (specify one of the piece parts (2)).
1) With the help of the functions of the SEAMS tab
“Indention”, “Corner”, “Fox ear” you can design cut sections on the pieces with seam allowances.
2) For superposed pieces, the function works on the extension of the cut line, if this line does not reach the piece border. For free pieces, the function works exactly along the cut line
Cut off a piece
To cut off a part of a piece:
- Select the tab MODELING and the button
in the tab. The cursor view changes to
. It is also possible to follow text menu points «Piece/ Model/ Cut a piece». - Specify a line for cutting a piece (1)
- Specify the remaining part of a piece (2). One specified part of a piece remains on the screen.
Additional mode is same as described for the function
«Cut a piece»
When selecting the remaining part of a piece, it is best not to select a section, from which the cut line runs, but choose a section adjacent to it instead. If a cut line does not run from a final point, it is possible that separate parts of a piece in the graded nest will be clicked .
ATTENTION! This method of selecting the working section (remaining, rotated, moved) works for other modeling functions as well.
Other specifics are the same as described for the function
«Cut a piece into 2 parts»
Widen a piece
To widen a piece (for example, to form folds and tucks):
It is also possible to follow text menu points «Piece/Model/ Widen piece».
- Specify cut line (1)
- Specify a part of a piece to be moved (2). The window with widening parameters is displayed on the screen:
Set widening value in the window «Widen by» and select a type of widening:
- widening will take place at normal to chord (in other words – to the straight line, which connects final points of the cut line).
- Widening in the coordinate system ХУ, on rotated axis
as well. Additional windows for entering X and Y values are displayed in the window with widening parameters:
When widening in the mode «At normal to chord», a specified side (2) determines positive direction for moving the selected part of a piece. (2а – moving a part to the right, 2б – to the left)
- Press the YES button to confirm data input, press CANCEL to cancel.
Additional mode (working without a cut line) is the same as described for the function
«Cut a piece»
1) When working with superposed pieces, upon specifying a side to be widened, a piece that was fixed upon superposition must be selected.
2) Functions of the tab SEAMS
«Designing a dart» (for Cut contour) and
«Set dart point» (for the main contour) can be used to design ends of the widened section.
Other specifics are the same as described for the function
«Cut a piece»
Conic spread
The function allows to rotate selected sections of a piece by a set value. To do so:
It is also possible to follow text menu points «Piece/Model/ Conic spread».
- Specify a point which is rotation center (1) (a point on the cut line),
- Specify a point (2) for setting opening
- Specify a part of a piece to be rotated (3). The window of function parameters is displayed on the screen:
- Set the spread value in the cell «Spread». When a positive value is entered, spread action is performed, when a negative value is entered - closing (piece sections «cover» each other).
To enter spread values differing by size, press the button
.The window is displayed on the screen:
It is possible to enter values differing by size manually (button
), or from the buffer (button
).
To confirm spread value press the YES button, to cancel - the CANCEL button.
Other functions of data input:
- read from buffer or input to buffer calculation of «Seam algebra»
- save to file or read from file
- clear the table
- Determine a section of a piece to be rotated:
- rotation only of one, specified section of a piece
- rotation of both sections of a piece to different sides symmetrical to the cut line.- Select type of cut design upon tearing «Cut», «Dart», «Tuck»:
It is possible to set value of sections at the end of a tuck in the mode
- Press the YES button to confirm spread parameters, press CANCEL to cancel.
Additional mode (without cut line) is the same as described for the function
«Cut a piece into 2 parts»
1) When the function is performed for a broken line, it is possible to specify any point of the broken line as a point for creating spread.
For example: creating a dart under a lapel by using a part of a bust dart opening:
2) For superposed pieces, the function does not work along the cut line, but only at points (additional mode with holding the <CTRL> key prior to using the function). A message is displayed:
3) An option for designing cuts «Cut out» is not applicable to superposed pieces (as inessential).
4) To perform the function with superposed pieces, pieces should be superposed without a gap between them along the spread line. Otherwise values of INTERMEDIATE spread on these pieces will differ: spread will be calculated for the second piece on account of the gap between pieces.
5) The functions of the tab SEAMS
«Dart design» (for Cut contour) and
«Set dart point» (for the main contour) can be used to design the end of the spread.
Widen and spread a piece (folds)
To widen a part of a piece with further spread (creating gathers, folds, etc.):
It is possible to follow text menu points «Piece/Model/Widen + spread a piece».
- Specify the end of a cut line near the first point (1)
- Specify the end of a line near the second point (2)
- Specify a section of a piece to be rotated (3). The window with parameters for widening is displayed on the screen:
- Set opening in the first and second point accordingly by using cells «Opening №1» and «Opening №2». When a positive value is entered, a piece is spread, when a negative value is entered - it is closed (piece section «cover» each other). It is possible to set opening in one point and joining in another.
To enter spread values differing by size, press the button
. Standard input window is displayed on the scree, where it is possible to enter values manually (button
), or from the buffer (button
).
- Specify a section of a piece to be rotated by switching on a require option in the setting «Rotate»:
- rotation of only one, specified part of a piece
- rotation of both parts of a piece to different sides, symmetrically with reference to the cut line.
- To confirm spread parameters press the YES button, to cancel - press CANCEL.
To create several folds, draft several cut lines on a piece and perform the function for each line one by one.
The functions of the tab SEAMS
«Dart design» (for Cut contour) and
«Set dart point» (for the main contour) can be used to design the end of the spread.
The mode
is used to perform double spread (box pleat). To construct it, switch on the mode «Box pleats» in the parameters window, and enter total value of spread in cells «Opening №1» and «Opening №2». The spread function will be performed twice, to both sides of pressing the fold towards the center.
It is possible to enter zero spread, but only for all sizes of a graded nest, otherwise the graded nest will be incorrect (there are fold sections in some sizes, but not in others)
The function of the tab SEAMS
- «Designing box pleat» is used to design the pleat, setting points with reference to the press direction:
Moving a dart
To move a dart:
It is also possible to follow text menu points «Piece/ Model/ Move a dart».
- Specify a fixed side of a dart (1) on the main contour
- Specify a side of a dart to be moved (2) on the main contour
- Specify the center of a dart (3) on the main contour
- Specify a cut line (4). The window of parameters for moving the dart is displayed on the screen:
- Select the value of dart movement, by switching on a required option of the parameter «Close»:
- part from the general opening of a dart (1.0 – entire opening, 0.5 – half of the opening, etc.)
- value in working measurement units (centimeters, millimeters, inches)
- Select type of a cut design in place of the shift. To do so, select an option of the parameter «Tear» - lock, cutting out or tuck (with setting length of segments at the end of the tuck)
When a dart is moved partially, select design type and place of a tear, and the remaining part.
- Select an option for compensating difference of sides by selecting an option of the setting «Deform».
If dart sides are different in length, sections of closing the darts can be designed by deforming :
- one of the dart sides will become shorter, the other one - longer, averaging out both lengths.
- only flexible part of a piece will be corrected in length.
- only fixed part of a piece will be corrected in length.
- side lengths do not change, additional section will be constructed in the place of closure.
- To confirm shift parameters press the YES button, to cancel - press CANCEL.
To transfer a dart to several places at once:
- After the function has been selected, specify a fixed side (1), side to be moved (2) and a point - center of the dart (3) on the main contour.
- Specify one or several points - areas for transferring the dart - while holding down the <SHIFT> key of the keyboard.
To move a dart to several points specify points (4,5,6) on the main contour one by one. The dart is moved to several places directly without constructing a cut line.
To move a dart to several lines, final points (4,5,6) o cut lines (figured, broken) need to be specified one by one, it is mandatoryto switch off sensitivity of the main contour
1) Dart movement is not applicable to superposed pieces. 2) Dart sides are specified only on the main contour (Working cut or Finished view).
3) When several movement places are selected, the command
«Cancel last selection» works only without letting go of the <SHIFT> key.
4) When the function is performed, contours «Grain line» and «Title», «Text» are not moved.
Close a dart
The function is often used to move a dart to a seam when a piece is being cut. So, by cutting off a yoke on a skirt, it is possible to close the dart on it and it will be automatically transferred to the seam, to which a yoke is stitched.
To close a dart:
It is also possible to follow text menu points «Piece/ Model/ Close a dart».
- Specify a fixed side of a dart (1) on the main contour
- Specify a side of a dart which will be rotated (2) on the main contour
- Specify a point - dart center (3) on the main contour. The window of function parameters is displayed:
- Enter a portion of closing the total opening of a dart in the cell File:embim1515.png (1.0 – entire opening, 0.5 – half, etc.)
- Select an option for rotating piece parts by switching on an option «Rotate»:
- Select a version of an option «Deform» for different length of dart sides:
- one of the dart sides will become shorter, the other will be extended, averaging out both lengths .
- only a fixed part of a piece will be corrected in length.
- only a movable part of a piece will be corrected in length.
- Length of dart sides is unchanged, a section is constructed in the place of closure.
Compensation of dart sides is not performed upon a partial dart closure.
- Press the YES button to confirm parameters, press CANCEL to cancel.
1) Dart movement is not applicable to superposed pieces.
2) Dart sides are specified only on the main contour (Working cut or Finished view).
3) When the function is performed, contours «Grain line» and «Title», «Text» are not moved. 4) If the dart center is not an extreme point of a piece (entire piece of a skirt, not a cut off yoke), the opening of a dart being closed is moved to a line, which is extension of the line in the middle of a dart:
Assemble a piece
The function is used to create a new piece by assembling it from suitable construction elements of one or several superposed pieces. It is possible to superpose several pieces, placing them over each other, draft required inner contour, construct seams – in other words, prepare all composing lines of a new piece. For example, to construct forepart lining, place a piece of under-lapel section on the forepart, draft required seam width along the stitching line of the under-lapel section, and perform piece assembly function according to the created reference lines. It is possible to construct a seamless sleeve via the graphic method, by superposing pieces of a sleeve and a bodice in a required manner, etc.
To assemble a piece:
It is also possible to follow text menu points «Piece/ Model/ Assemble a piece»
- The assembly parameters window is displayed on the screen, a type of a assembled contour must be selected in this window (this will be the main contour of a future piece): Finished view or Cut.
ATTENTION! When a Cut type is selected, two contours are automatically created: the main contour – Working, and a contour that copies it (derived) – Cut, which will be drafted in the layouts.
- Specify parts of a new piece clockwise one by one. It is possible to specify sections of any contours: finished view (1,2,5,6), cut, inner contours (3,4), grain line.
It is recommended to begin assembly from a section with defined borders or from a locked section.
- Select the type of connecting sections.
- Select the type of connecting sections.
Sections may not have exact superposition (not reach the next section or cross it with extension), so one of the types of the setting «Combination» must be selected:
- crossing of the specified sections will be found upon assembling a piece. This is the connection type that is used most often.
ATTENTION! Parts, which continue beyond the border of crossing the following assembled section (beyond the place of connection), MUST be specified on that section of a piece, which will be included in the future piece.
For example, when assembling an under-lapel piece from lines of the inner contour and forepart sections, the shoulder section must be specified as close as possible to the neck (if the shoulder section is whole)
- specified sections are connected with a straight line.
After this mode is selected, assembled section must be specified near its beginning.
- specified sections will be connected at an average line between them (for example, if sections do not match exactly and pieces are almost parallel).
After this mode is selected, assembled section must be specified near its beginning.
Order of selecting connection: Select a section, then select the mode of connecting this section to the next section (Crossing, Averaging, Section insertion). Select a section again (the following section, for connecting with which the mode was selected), then, if a mode changes, select the mode again, etc.
- It is possible to change the grain line direction of a new piece by selecting a required option in the setting «Grain line»
- similar to the grain line placement of the first specified section.
- horizontally with reference to the screen.
- vertically with reference to the screen. - If necessary, inner contours can be input in the new piece (to draft a supporting line, a mark on a new piece at once). To do so: select the button
(or another contour type) after assembling the main contour, and specify sections of an inner contour. The button
is used to assemble another contour (for example, contour of a dart and a pocket). - Click the right mouse button. A new (untitled) piece is displayed on the screen.
The function parameters window remains on the screen and it is possible to assemble a new piece.
- Press the CANCEL button to finish using the function.
1)Cancel the last selected element
If a section (or several sections) is selected in error while using the function, it is possible to cancel the last section selection. Without quitting the function «Assemble a piece» (without clicking the right mouse button), click the button
of the screen button menu as many times as the number of elements to be canceled. After this, proceed with assembling a piece.
2)Stop command performance
The button
of the screen button menu is activated while working with the function «Assemble a piece», this button allows to quit command performance without creating incorrect pieces on the screen
3) Clicking a section in a given size determines the place of a click proportionally for an entire graded nest. It is possible that in different sizes a place of a click will be on different sides from the following crossing section (if increment value in a point has a wide range).
In this case it is recommended to specify a section in a different area, with a clear location in the entire graded nest.
4) If incorrect crossing of sections results from the assembly process, error message is displayed but a piece is displayed on the screen. In this case, a piece will be automatically locked with segments, but it is necessary to check possibility of crossing for specified sections in graded nest sizes.
5) When specifying assembled sections, it is possible to switch off sensitivity and contour visibility (panel of contour visibility in the screen button menu) at the same time.
6) When 2 points of line crossing are present, there is a problem of selecting one of them, which can result in an incorrect assembly. For example, having superposed a forepart and a side section of a jacket in 2 points, it will not be possible to assemble a whole detail, if relief seams consist of one section. Two crossing points are created - on the shoulder and on the bust, the program will arbitrarily select one of these points –for example, on the shoulder. As a result, we have a piece with «intertwining» on the relief seam – a view fully similar to the two superposed pieces. In this case, relief section should have been divided into several parts before assembly («cut» bust points, making them Final).
7) It is possible to set a required main contour in the program settings (text menu points «Settings/ Program parameters», tab GENERAL/ Constructor) while performing the function, which will always be displayed by default when the command button is selected.
8) If it is necessary to assemble a piece with a different number of sections (for example – a forepart, where a dart is constructed in some sizes), assembly must be started with the first (clockwise) common section after the dart. In other words, dart sections, which are not present in some sizes, have to be last in the assembly process and have large numbers, common for them.
Join two pieces
To join two pieces together:
It is also possible to follow text menu points «Piece/Model/Join two pieces».
- Specify the beginning of a section being copied (1) and the beginning of a section being replaced (2)
- Specify the end of section being copied (3) and the end of a section being replaced (4).
- A window is displayed on the screen, where YES button must be pressed to confirm function performance
If an option «Deform ends» is switched on, difference in section lengths will be made equal. When this mode is switched off, difference in length is compensated by a locking section.
As a result of the function performance, only a piece, specified for section replacement, is changed: its «replaced» sections disappear, instead of them, «copied» sections are inserted in the contour (clockwise) as if «gluing» 2 pieces. A piece, which sections were copied, remains unchanged.
This function is almost completely the same as the function
«Section/ Replace section».
Spread a piece
To spread a piece conically by a set number of folds with a required opening:
- Select the tab MODELING and the button
in the tab. The cursor view changes to
. It is also possible to follow text menu points «Piece/ Model/ Spread a piece» - Specify a section (1) – place of location for rotation centers of a piece.
It is possible to specify several sections by holding down the <SHIFT> key of the keyboard. It is possible to specify a portion of a section by specifying its 2 points while pressing the <CTRL> key (and releasing at once).
- Specify a rotated section of a piece (2). The window of data input is displayed on the screen:
- Enter total spread value in the cell «Opening».
To enter different values by size use the button of size-by-size input
. Standard data input window is displayed on the screen:
It is possible to enter values different by size manually (button
), or from the buffer (button
).
- Set required spread parameters:
- two sides of a fold will be drafted on a piece - the line of actual spread
When a number of lines is set automatically, step between them equals 1cm. If automatic setting is switched off, the cell «Number of lines» will be unblocked, and it will be possible to enter a required number of spread lines by hand.
- Press the YES button to confirm spread parameters, press CANCEL to cancel.
The reference section (1) (or several section, or a portion of a section) will be divided equally according to the set number of lines - normals, and conic spread will be performed with equal division of a total opening value by a number of folds.
1)Existing points are saved on the section, which will be spread, but new points are not inserted at the level of spread lines.
Points can be input manually by using the function
- «Point/ Input point at crossing».
2)The function is not applicable to superposed pieces.
Spread a piece by lines
The function allows to perform conic spread of a piece by several cut lines at once.
Cut lines can be drafted arbitrarily on a piece (the function
- «Contour/ Create new contour»), or using the function of the LINES tab and macrocommands for creating contours. Lines can be straight or figured (but not broken)
To perform conic spread of a piece by lines:
It is also possible to follow text menu points «Piece/ Model/ Spread a piece by lines»
- Specify a line of a spread (inner contour or sight contour) near the center of piece rotation.
It is possible to specify several lines for spreading (1,2,3,4,5,6,7) one by one while holding down the <SHIFT> key of the keyboard. The data input window is displayed on the screen:
- Enter total spread value in the cell «Opening».
To enter different values by sizes use the size-by-size input button
. Standard data input window is displayed on the screen:
It is possible to input values different by size manually (button
), or from the buffer (button
).
- Set required spread parameters:
- two sides of a fold will be drafted on a piece - a line of actual spread
- symmetrical spread to both sides from each spread line.
When a parameter is switched off, spread direction is determined by the first of specified lines.
- allows to smooth out a section automatically after spreading. It is possible that ends of spread lines will not match the smoothed curve:
- Press the YES button to confirm spread parameters, press CANCEL to cancel.
Conic spread will be performed along all specified lines with equal division of the total opening value by a number of lines
If only one spread line is used:
- Specify spread line (1) (inner contour or sight contour) near the center of piece rotation.
- Specify a section of a piece to be rotated (2).
It is still possible to use the switch «To both sides», when both parts of a piece will be rotated on the screen with reference to the cut line.
This mode differs from the function «Conic spread»
because a number of sections on a piece will not change, and due to this, zero value input is applicable for some sizes when working with the buffer of «Seam algebra». For example, it is possible to correct cap length when working with models on the basis of previously used models.
Specifics are similar to those described for the function
- «Piece/ Model/ Spread a piece»



















































